LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2016 >> BRZ Premium >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 2 (Automatic Transmission (Service Information)) >> TRANSMISSION VALVE BODY Assembly >> Unit Inspection

Unit Inspection

WARNING: This page is about a different variant/trim than selected.
  1. Check of clutch control solenoid No. 1 (SL2)
    1. Measure the resistance between the terminals.

      Resistance

      Inspection terminals Inspection conditions Standard value
      Clutch control solenoid No. 1 (SL2) terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6Ω
      Fig 1: Checking Clutch Control Solenoid No. 1 (SL2) Connector Terminals
      G10214270Courtesy of SUBARU OF AMERICA, INC.
    2. Connect the battery positive to terminal 1 of the clutch control solenoid No. 1 (SL2) via the 12 V-21 W valve and check that the valve in the solenoid operates when connecting the battery ground to terminal 2.

      Criteria: Operates (with operating noise)

  2. Check of lock-up control solenoid (SLU)
    1. Measure the resistance between the terminals.

      Resistance

      Inspection terminals Inspection conditions Standard value
      Lock-up control solenoid (SLU) terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6Ω
      Fig 2: Checking Lock-Up Control Solenoid (SLU) Connector Terminals
      G10214271Courtesy of SUBARU OF AMERICA, INC.
    2. Connect the battery positive to terminal 2 of the lock-up control solenoid (SLU) via the 12 V-21 W valve and check that the valve in the solenoid operates when connecting the battery ground to terminal 1.

      Criteria: Operates (with operating noise)

  3. Check of line pressure control solenoid Assembly (SLT)
    1. Measure the resistance between the terminals.

      Resistance

      Inspection terminals Inspection conditions Standard value
      Line pressure control solenoid Assembly (SLT) terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6Ω
      Fig 3: Checking Line Pressure Control Solenoid Assembly (SLT) Connector Terminals
      G10214272Courtesy of SUBARU OF AMERICA, INC.
    2. Connect the battery positive to terminal 2 of the line pressure control solenoid Assembly (SLT) via the 12 V-21 W valve and check that the valve in the solenoid operates when connecting the battery ground to terminal 1.

      Criteria: Operates (with operating noise)

  4. Check of clutch control solenoid No. 1(SL1)
    1. Measure the resistance between the terminals.

      Resistance

      Inspection terminals Inspection conditions Standard value
      Clutch control solenoid No. 1 (SL1) terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6Ω
      Fig 4: Checking Clutch Control Solenoid No. 1 (SL1) Connector Terminals
      G10214273Courtesy of SUBARU OF AMERICA, INC.
    2. Connect the battery positive to terminal 1 of the clutch control solenoid No. 1 (SL1) via the 12 V-21 W valve and check that the valve in the solenoid operates when connecting the battery ground to terminal 2.

      Criteria: Operates (with operating noise)

  5. Check of transmission 3 way solenoid Assembly (SR)
    1. Measure the resistance between the terminals.

      Resistance

      Inspection terminals Inspection conditions Standard value
      Transmission 3 way solenoid Assembly (SR) connector - body 20°C (68°F) 11 to 15Ω
      Fig 5: Checking Transmission 3 Way Solenoid Assembly (SR) Connector Terminals
      G10214274Courtesy of SUBARU OF AMERICA, INC.
    2. Connect the battery positive to the connector of the transmission 3 way solenoid Assembly (SR) and check that the valve in the solenoid operates when connecting the battery ground to the solenoid body.

      Criteria: Operates (with operating noise)

  6. Check of transmission 3 way solenoid Assembly (S1)
    1. Measure the resistance between the terminals.

      Resistance

      Fig 6: Checking Transmission 3 Way Solenoid Assembly (S1) Connector Terminals
      G10214275Courtesy of SUBARU OF AMERICA, INC.
    2. Connect the battery positive to the connector of the transmission 3 way solenoid Assembly (S1) and check that the valve in the solenoid operates when connecting the battery ground to the solenoid body.

      Criteria: Operates (with operating noise)

      Inspection terminals Inspection conditions Standard value
      Transmission 3 way solenoid Assembly (S1) connector - body 20°C (68°F) 11 to 15Ω
  7. Check of transmission 3 way solenoid Assembly (S4)
    1. Measure the resistance between the terminals.

      Resistance

      Inspection terminals Inspection conditions Standard value
      Transmission 3 way solenoid Assembly (S4) connector - body 20°C (68°F) 11 to 15Ω
      Fig 7: Checking Transmission 3 Way Solenoid Assembly (S4) Connector Terminals
      G10214276Courtesy of SUBARU OF AMERICA, INC.
    2. Connect the battery positive to the connector of the transmission 3 way solenoid Assembly (S4) and check that the valve in the solenoid operates when connecting the battery ground to the solenoid body.

      Criteria: Operates (with operating noise)

  8. Check of transmission 3 way solenoid Assembly (S2)
    1. Measure the resistance between the terminals.

      Resistance

      Inspection terminals Inspection conditions Standard value
      Transmission 3 way solenoid Assembly (S2) connector - body 20°C (68°F) 11 to 15Ω
      Fig 8: Checking Transmission 3 Way Solenoid Assembly (S2) Connector Terminals
      G10214277Courtesy of SUBARU OF AMERICA, INC.
    2. Connect the battery positive to the connector of the transmission 3 way solenoid Assembly (S2) and check that the valve in the solenoid operates when connecting the battery ground to the solenoid body.

      Criteria: Operates (with operating noise)

  9. Check of transmission 3 way solenoid Assembly (S3)
    1. Measure the resistance between the terminals.

      Resistance

      Inspection terminals Inspection conditions Standard value
      Transmission 3 way solenoid Assembly (S3) connector - body 20°C (68°F) 11 to 15Ω
      Fig 9: Checking Transmission 3 Way Solenoid Assembly (S3) Connector Terminals
      G10214278Courtesy of SUBARU OF AMERICA, INC.
    2. Connect the battery positive to the connector of the transmission 3 way solenoid Assembly (S3) and check that the valve in the solenoid operates when connecting the battery ground to the solenoid body.

      Criteria: Operates (with operating noise)

scientia non olet · About LEMON Manuals