Special Tool
WARNING: This page is about a different variant/trim than selected.
| ILLUSTRATION | TOOL NUMBER | DESCRIPTION | REMARKS |
|---|---|---|---|
| 398791700 | REMOVER | Used for removing and installing the straight pin (6 mm). | |
| 399527700 | PULLER SET | Used for removing and installing the roller bearing (differential).
|
|
| 498515700 | REMOVER | Used for removing the roller bearing of the transfer driven gear. | |
| 498247001 | MAGNET BASE |
|
|
| 498247100 | DIAL GAUGE |
|
|
| 498077000 | REMOVER | Used for removing the differential taper roller bearing. | |
| 899858600 | REMOVER | Used for removing the roller bearing. | |
| 499757002 | INSTALLER | Used for installing the bearing cone of transfer driven gear (transmission case side). | |
| 18630AA010 | WRENCH COMPL RETAINER |
|
|
| 499877000 | RACE 4-5 INSTALLER |
Used for disassembling the driven shaft and transfer driven gear. | |
| 899864100 | REMOVER | Used for removing the transmission main shaft and drive pinion parts. | |
| 498057300 | INSTALLER | Used for installing the extension oil seal. | |
| 498255400 | PLATE | Used for measuring backlash. | |
| 41099AA011 | ENGINE SUPPORT BRACKET |
|
|
| 41099AA020 | ENGINE SUPPORT | Used for supporting engine. | |
| 398527700 | PULLER ASSY |
|
|
| 398643600 | GAUGE | Used for adjusting total end play, extension end play and drive pinion shim. | |
| 398177700 | INSTALLER |
|
|
| 399893600 | PLIER |
|
|
| 18756AA000 | CLAW |
|
|
| 499247400 | INSTALLER | Used for installing the ball bearing of the transfer drive gear. | |
| 398497701 | SEAT |
|
|
| 398437700 | INSTALLER | Used for installing the front differential side bearing. | |
| 18632AA000 | STAND ASSY | Used for disassembling and assembling the transmission. | |
| 18671AA000 | OIL SEAL GUIDE |
|
|
| 18657AA010 | INSTALLER |
|
|
| 18657AA000 | INSTALLER |
|
|
| 18758AA000 | PULLER | Used for removing the transfer driven gear rear bearing outer race. | |
| 18831AA000 | GAUGE | Used for selecting the transfer driven gear bearing adjusting washer. | |
| 18631AA000 | HANDLE | Used for measuring the front differential backlash. | |
| 18754AA000 | REMOVER | Used to remove parts of the driven gear. | |
| 18665AA000 | HOLDER |
|
|
| 18666AA000 | HOLDER |
|
|
| 18667AA000 | HOLDER |
|
|
| 18664AA000 | BASE |
|
|
| 18722AA010 | REMOVER | Used for disassembling the main shaft. | |
| 18651AA000 | INSTALLER | Used for assembling the main shaft. | |
| 18852AA000 | TORQUE WRENCH |
|
|
| 18668AA000 | PUNCH | Used to crimp the main shaft lock nut. | |
| 18669AA000 | PUNCH | Used to crimp the driven shaft lock nut. | |
| 18670AA000 | PUNCH | Used to crimp the drive pinion shaft lock nut. | |
| 18620AA000 | ADAPTER WRENCH | Used for removing and installing the driven gear shaft lock nut. | |
| 18621AA000 | ADAPTER WRENCH | Used for removing and installing the drive pinion shaft lock nut. | |
| 18723AA000 | REMOVER | Used for disassembling the driven shaft. | |
| 18630AA000 | WRENCH ASSY | Used for removing and installing the differential side retainer LH. | |
| 18672AA000 | GUIDE CLIP | Used for installing the reverse idler snap ring. | |
| 18720AA000 | REMOVER | Used for disassembling the main shaft. | |
| 18654AA000 | INSTALLER | Used for assembling the driven shaft. | |
| 18663AA000 | SOCKET | Used for removing and installing the transfer bearing holder. | |
| 18853AA000 | HEIGHT GAUGE |
|
|
| 18760AA000 | CLAW |
|
|
| 18675AA000 | DIFFERENTIAL SIDE OIL SEAL INSTALLER | Used for installing the differential side retainer oil seal. | |
| 28399SA010 | OIL SEAL PROTECTOR | Used for protecting oil seal when installing front drive shaft. | |
| 18657AA020 | OIL SEAL INSTALLER | Used for installing the oil seal. | |
| 18270KA020 | SOCKET (E20) | Used for removing and installing the hypoid driven gear. |