LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2013 >> Legacy Premium, Automatic CVT Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 9 (Manual Transaxle & Differential) >> General Description >> Preparation Tool >> Special Tool

Special Tool

WARNING: This page is about a different variant/trim than selected.
ILLUSTRATION TOOL NUMBER DESCRIPTION REMARKS
G05002464
 899524100 PULLER SET Used for removing the front differential roller bearing.
  1. Puller
  2. Cap
G05002914
 399780104 WEIGHT Used for adjusting preload on the front differential roller bearing.
G05002433
 498077000 REMOVER
  • Used for removing the roller bearing of the drive pinion shaft.
  • Used for removing the transfer driven gear taper roller bearing.
G05002454
 498077600 CENTER DIFFERENTIAL BEARING REMOVER Used for removing the center differential ball bearing.
G05342049
 498147001 DEPTH GAUGE Used for adjusting the extension end play and main shaft end play.
G05002441
 498247001 MAGNET BASE
  • Used for measuring the backlash of bevel pinion gear and hypoid gear.
  • Used together with DIAL GAUGE (498247100).
G05002442
 498247100 DIAL GAUGE
  • Used for measuring the backlash of bevel pinion gear and hypoid gear.
  • Used together with MAGNET BASE (498247001).
G07914986
 18667AA020 HOLDER
  • Used for removing and installing the drive pinion shaft lock nut.
  • Used for measuring the backlash of hypoid gear.
  • Used for adjusting preload on the front differential roller bearing.
G05002921
 498937000 TRANSMISSION HOLDER Used for removing and installing the main shaft lock nut.
G05002922
 499277100 BUSHING 1-2 INSTALLER
  • Used for installing the drive pinion shaft washer.
  • Used for installing the front differential roller bearing outer race.
G05002923
 499277200 INSTALLER
  • Used for installing the 2nd driven gear bushing, roller bearings, 3rd-4th driven gear, 5th driven gear and the 6th driven gear.
  • Used for installing the drive pinion shaft washer.
G08541036
 927640000 INSTALLER Used for installing the roller bearing (transfer case side) of transfer driven gear.
G05002925
 18630AA010 WRENCH COMPL RETAINER
  • Used for removing and installing the differential side retainer.
  • Used for adjusting preload on the front differential roller bearing.
  • WRENCH COMPL RETAINER (18630AA020) can also be used.
G07914992
 18722AA000 REMOVER Used for removing the 5th drive gear and 6th drive gear.
G05002928
 499877000 RACE 4-5 INSTALLER
  • Used for installing the 4th, 5th and 6th drive gear needle bearing races and the main shaft double taper roller bearings.
  • Used together with REMOVER (899714110).
G05002929
 499917500 DRIVE PINION GAUGE ASSY Used for adjusting the drive pinion shaft shim.
G05002930
 499927100 HANDLE Used for backlash measurement of the hypoid gear and preload adjustment of the front differential roller bearing.
G05002931
 499937100 TRANSMISSION STAND Used for disassembling and assembling the transmission.
G05002932
 499987003 SOCKET WRENCH (35) Used for removing and installing the main shaft lock nut.
G07914998
 499987300 SOCKET WRENCH (50) Used for removing and installing the driven shaft lock nut.
G05002934
 899714110 REMOVER Used for removing and installing the parts of main shaft and driven shaft.
G05002935
 899864100 REMOVER
  • Used for removing the parts of the main shaft.
  • Used for removing the transfer driven gear roller bearing (transfer case side) and for installing it (extension case side).
  • Used for removing the transfer drive gear ball bearing.
G06652232
 18680AA020 HOLDER
  • Used for removing and installing the drive pinion shaft lock nut.
  • Used for removing and installing the driven shaft lock nut.
G05002937
 899904100 STRAIGHT PIN REMOVER Used for removing and installing the straight pin.
G05002462
 398497701 ADAPTER
  • Used for installing the front differential roller bearing.
  • Used together with BUSHING 1-2 INSTALLER (499277100).
G05002432
 498057300 INSTALLER Used for installing the extension case oil seal.
G05002439
 498255400 PLATE Used for measuring the hypoid gear backlash.
G05002431
 398527700 PULLER ASSY
  • Used for removing the extension case oil seal.
  • Used for removing the front differential side retainer bearing outer race.
  • Used for removing the front differential side retainer oil seal.
G05002448
 398643600 GAUGE Used for adjusting the extension end play.
G05002948
 398177700 INSTALLER
  • Used for installing the transfer drive gear ball bearing.
  • Used for installing the 4th drive gear needle bearing race.
G05342994
 498175500 INSTALLER Used for installing the roller bearing of transfer driven gear (extension case side).
G05002461
 28399SA010 OIL SEAL PROTECTOR Used for protecting the oil seal from damage when inserting the front drive shaft.
G05002460
 18675AA000 DIFFERENTIAL SIDE OIL SEAL INSTALLER Used for installing the front differential side retainer oil seal.
G05003164
 398791700 SPRING PIN REMOVER 2 Used for installing and removing the spring pin.
G06652243
 18662AA010 SOCKET (27) Used for removing and installing the drive pinion shaft lock nut.
G06652244
 899754112 PRESS
  • Used for removing driven shaft parts.
  • Used to install the main shaft ball bearing.
G05003194
 18631AA000 HANDLE Used for installing transfer case assembly and extension case assembly.
G05022174
 18762AA000 COMPRESSOR SPECIAL TOOL Used for removing the 1st driven gear.
G05003214
 18654AA000 INSTALLER Used for installing the 2nd driven gear bushing.
G05003191
 18657AA000 INSTALLER Used for installing the transfer case oil seal.
G08581895
 41099AJ130 SPECIAL TOOL FB Used for removing and installing transmission.
G06654300
 99099AJ000 ENGINE HANGER
  • Used for removing and installing transmission.
  • Used together with CHAIN BALANCER (99099AJ010) and sling chain (general tool).
G06654301
 99099AJ010 CHAIN BALANCER
  • Used for removing and installing transmission. (Weight of 350 kg (772 lb) is supported)
  • Used together with ENGINE HANGER (99099AJ000) and sling chain (general tool).
  • Used to hang the engine while balancing it with the sling chain inserted in this tool.
G07915021
 498267200 CYLINDER HEAD TABLE Used for installing and removing the roller bearing of the transfer case.
G07915022
 498267300 CYLINDER HEAD TABLE Used for installing and removing the roller bearing of the transfer case.
G08581900
 18763AA000 COMPRESSOR SHAFT Used for installing and removing the needle bearing of the transfer case.
G04997553
 498277200 STOPPER SET
  • Used for installing the needle bearing of the transfer case.
  • Use only the spacer.
scientia non olet · About LEMON Manuals