List Of Self-Diagnosis Mode Operation
Normal meter
SELF-DIAGNOSIS MODE OPERATION CHART
| Speedometer, tachometer, fuel gauge, engine coolant temperature gauge | Microcomputer running type warning light, indicator light | AT select lever position indicator light | ODO/Trip indicator | SPORT shift indicator | Illumination (indicator needle, plate, ring, LCD) | Buzzer (SPORT shift buzzer, VDC buzzer) |
|---|---|---|---|---|---|---|
| Step 0. Processing to self-diagnosis function | ||||||
| Operating initial operation | Initial illuminating | Normal | Normal | Initial illuminating | Initial illuminating | Not beep. |
| Step 1-1. Check each indication after initial operation | ||||||
| Repeat the sweep operation (After holding on lowest position for one second, reaches to highest position within 5 seconds, and after holding on highest position for one second, reaches to lowest position within 5 seconds). | Light ON | With the highest brightness, illuminate the position sequentially at a cycle of 1.5 seconds. | Perform the segment check. For the illumination order, refer to the illumination order table. | Perform the segment check. For the illumination order, refer to the illumination order table. | Light at the highest brightness. | Not beep. |
| Step 1-2. Press the trip knob (trip knob input is not accepted till the meter indicator needle reaches the highest position): sweep complete, AT select lever position indicator display is set | ||||||
| After completing sweep in step 1-1, back to lowest position. | Light ON | Keep the position indicated when the trip knob is pressed. | Underbar "___" is displayed. | "1" is displayed. | Light at the highest brightness. | Not beep. |
| Step 2-1. Press the trip knob, and hold it: Check each meter | ||||||
| All meters are moved simultaneously in every 0.5 seconds from the lowest position to highest position. Speedometer/Tachometer: Approx. 5 degrees at every movement. Engine coolant temperature/Fuel gauge: Moves approx. 2 degrees at a time. | Light OFF | Keep the position indicated that set instep 1-2. | Display the current meter directing angle on odometer. Ex.) When the speedometer/tachometer: 135 degrees and engine coolant temperature gauge/fuel gauge: 54 degrees, displays "135054". | "↓2" is displayed. | Light at the highest brightness. | Not beep. |
| Step 2-2. Release the trip knob: Specifying the meter directing position | ||||||
| Stop at directing position when the trip knob is released. | Light OFF | Keep the position indicated that set instep 1-2. | Display the current meter directing angle on odometer. | "2" is displayed. | Light at the highest brightness. | Not beep. |
| Step 3-1. Press the trip knob, and hold it: Check illumination | ||||||
| Keep the position that specified at step 2-2. | Light OFF | Varying from the highest brightness (ILL6) to the lowest luminescence (ILL1) every second. After reaching at ILL1, repeat it from ILL6. | Illumination brightness is displayed. (From ILL6 to ILL1) | "↓3" is displayed. | Varying from the highest brightness (ILL6) to the lowest luminescence (ILL1) every second. After reaching at (ILL1), repeat it from (ILL6). | Not beep. |
| Step 3-2. Release the trip knob: Specifying the illumination brightness | ||||||
| Keep the position that specified at step 2-2. | Light OFF | Keep the brightness at the time when the trip knob is released. | Displays the brightness level at the time when the trip knob was released. | "3" is displayed. | Keep the brightness at the time when the trip knob is released. | Not beep. |
| Step 4-1. Press the trip knob: Check the beeping of SPORT shift buzzer (For AT model) | ||||||
| All meter indicator needle returns to lowest position. | Light OFF | Light at the highest brightness. Keep the position indicated that set instep 1-2. | Illumination brightness is displayed. | "↑ ↓ 8" is displayed. Blinks with buzzer. | Light at the highest brightness. | SPORT shift buzzer beeps. |
| Step 4-2. Press the trip knob: Check the VDC indicator light (Model with VDC) | ||||||
| All meter indicator needle returns to lowest position. | VDC warning light and VDC operation indicator light blink. | Light at the highest brightness. Keep the position indicated that set in step 1-2. | Illumination brightness is displayed. | "4" is displayed. | Light at the highest brightness. | VDC buzzer beeps. |
| Step 5. Press the trip knob: Complete the self-diagnosis 1 cycle | ||||||
| All meter indicator needle returns to lowest position, and go back to step 1 after completion. | ||||||
- Illuminating order tableILLUMINATING ORDER REFERENCE CHART
Illuminating order 1 2 3 4 5 6 7 8 9 10 11 Go back to 1 and repeat. Trip meter AB AB A B A B A B A B A B ODO/trip meter 8888.8 00000 1111.1 22222 3333.3 44444 5555.5 66666 7777.7 88888 9999.9 888888 000000 111111 222222 333333 444444 555555 666666 777777 888888 999999 SPORT shift indicator 8 1 2 3 4 5 1 2 3 4 5 ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↓ ↓ ↓ ↓ ↓ ↓ ↓ AT select lever position indicator P P R R R N N N D D D Display time (sec.) 1 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
Meter with multi-information display
SELF-DIAGNOSIS MODE OPERATION CHART
| Speedometer, tachometer, fuel gauge, engine coolant temperature gauge, ECO gauge | Microcomputer running type warning light, indicator light | AT select lever position indicator light | Multi-information display | Illumination (indicator needle, plate, ring, LCD) | Buzzer (SPORT shift buzzer, VDC buzzer, vehicle speed warning buzzer) |
|---|---|---|---|---|---|
| Step 0. Processing to self-diagnosis function | |||||
| Operating initial operation | Initial illuminating | Normal | TRIP: Normal ODO: Normal |
Initial illuminating | Not beep. |
| Step 1-1. Check each indication after initial operation | |||||
| Repeat the sweep operation (After holding on lowest position for one second, reaches to highest position within 5 seconds, and after holding on highest position for one second, reaches to lowest position within 5 seconds). | Light ON | Perform the segment check. For the illumination order, refer to the table 1 of illumination order tables. | STEP 1 is displayed. White illumination: 6 seconds. Yellow illumination: 6 seconds. | Light at the highest brightness. | Not beep. |
| Step 1-2. Press the trip knob: sweep completes, AT select lever position indicator display is set | |||||
| After quitting sweep in step 1-1, back to lowest position. (Until back to lowest position, ignore trip input.) | Light ON | Keep the position indicated when the trip knob is pressed. | Keep the illumination color indicated when the trip knob is pressed. | Light at the highest brightness. | Not beep. |
| Step 2-1. Press the trip knob, and hold it: Check each meter | |||||
| Perform the indicator needle check. For the illumination order, refer to the table 2 of illumination order tables. | Light OFF (Low fuel warning light follows the table 2 of tables.) | For the illumination order, refer to the table 2 of illumination order tables. | STEP 2 is displayed. White illumination: 12.5 seconds. Yellow illumination: 12.5 seconds. | Light at the highest brightness. | Not beep. |
| Step 2-2. Release the trip knob: Specifying the meter directing position | |||||
| Stop at directing position when the trip knob is released. (Indicator needle stops moving after movement is completed.) | Light OFF | Keep the position indicated when the trip knob is released. | Keep the illumination color at the time when the trip knob is released. | Light at the highest brightness. | Not beep. |
| Step 3-1. Press the trip knob, and hold it: Check illumination | |||||
| Keep the position that specified at step 2-2. | Light OFF | Keep the position that specified at step 2-2. | STEP 3 is displayed, then illumination brightness is displayed. (From ILL6 to ILL1) | Varying from the highest brightness (ILL6) to the lowest luminescence (ILL1) every second. After reaching at (ILL1), repeat it from (ILL6). | Not beep. |
| Step 3-2. Release the trip knob: Specifying the illumination brightness | |||||
| Keep the position that specified at step 2-2. | Light OFF | Keep the position that specified at step 2-2. | Keep the position indicated when the trip knob is pressed. | Keep the brightness at the time when the trip knob is released. | Not beep. |
| Step 4-1. Press the trip knob: Check the beeping of multi buzzer | |||||
| All meter indicator needle returns to lowest position. | Light OFF | P is displayed in white illumination. | STEP 3 WN BUZZER is displayed. White illumination: 1 second. Yellow illumination: 1 second. | Light at the highest brightness. | Buzzer beeps when multi information display is yellow illumination. |
| Step 4-2. Press the trip knob: Check the beeping of SPORT shift buzzer (For AT model only, while for MT model, go to next) | |||||
| All meter indicator needle returns to lowest position. | Light OFF | Shift display blinks with buzzer. | STEP 4 SS BUZZER is displayed. | Light at the highest brightness. | SPORT shift buzzer beeps. |
| Step 5. Press the trip knob: Complete the self-diagnosis 1 cycle | |||||
| All meter indicator needle returns to lowest position, and go back to step 1 after completion. | |||||
- Illuminating order table
Display Contents 1
ILLUMINATING ORDER REFERENCE CHART
| Illuminating order | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | Go back to 1 and repeat |
| ↑ | ↑ | ↑ | ↑ | ↑ | |||||||
| ↓ | ↓ | ↓ | ↓ | ||||||||
| AT select lever position indicator | P | R | N | D | All lights ON | 1 | 2 | 3 | 4 | 5 | |
| Display time (seconds) | 1 | 0.5 | 0.5 | 0.5 | 1 | 0.5 | 0.5 | 0.5 | 0.5 | 0.5 | |
| Back-up light | White light ON | ||||||||||
Display Contents 2
ILLUMINATING ORDER REFERENCE CHART
| Illuminating order | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | Go back to 1 and repeat. |
| Speedometer | 0 | 0 | 40 | 60 | 80 | 100 | 80 | 60 | 40 | 0 | |
| Tachometer | 0 | 0 | 1000 | 2000 | 3000 | 4000 | 3000 | 2000 | 1000 | 0 | |
| Fuel gauge | Lowest position | EMPTY | Warning light illumination position | 1/2 | FULL | Highest position | FULL | 1/2 | Warning light illumination position | EMPTY | |
| Engine coolant temperature gauge | Lowest position | C | at the first scale | 1/2 | at the third scale | over the fourth scale (approx. 120°C) | at the third scale | 1/2 | at the first scale | C | |
| ECO gauge | -Max | 0 | +Max | 0 | -Max | 0 | +Max | 0 | -Max | 0 | |
| Low fuel warning light | Light ON | Light ON | Light ON | Light OFF | Light OFF | Light OFF | Light OFF | Light OFF | Light ON | Light ON | |
| AT select lever position indicator | P | R | N | D | All lights ON | ↑ 1 | ↓ 2 | ↑ 3 | ↓ 4 | ↑ 5 | |
| Multi-information display | STEP 2 is displayed. | ||||||||||
| Display time (seconds) | 2.5 | 2.5 | 2.5 | 2.5 | 2.5 | 2.5 | 2.5 | 2.5 | 2.5 | 2.5 | |
| Back-up light (SS of AT model) | White light ON | ||||||||||
| Back-up light (Multi information display LCD) | White light ON | Yellow light ON | |||||||||