List Of Self-Diagnosis Mode Operation
LIST OF SELF-DIAGNOSIS MODE OPERATION
| Speedometer, tachometer, fuel gauge, engine coolant temperature gauge | Microcomputer running type warning light, indicator light | AT select lever position indicator light | ODO/Trip indicator | SPORT shift indicator | Illumination (indicator needle, plate, ring, LCD) | Buzzer (SPORT shift buzzer) |
| Step 0. Processing to self-diagnosis function | ||||||
| Operating initial operation | Initial illuminating | Normal | Normal | Initial illuminating | Initial illuminating | Not beep. |
| Step 1-1. Check each indication after initial operation | ||||||
| Repeat the sweep operation (After holding on lowest position for one second, reaches to highest position within 5 seconds, and after holding on highest position for one second, reaches to lowest position within 5 seconds). | Light ON | With the highest brightness, illuminate the position sequentially at a cycle of 1. 5 seconds. For the illumination order, refer to the illumination order table. | Perform the segment check. For the illumination order, refer to the illumination order table. | Perform the segment check. For the illumination order, refer to the illumination order table. | Light at the highest brightness. | Not beep. |
| Step 1-2. Press the trip knob (trip knob input is not accepted till the meter indicator needle reaches the highest position): sweep complete, AT select lever position indicator display is set | ||||||
| After completing sweep in step 1-1, back to lowest position. | Light ON | Keep the position indicated when the trip knob is pressed. | Under bar " - " is displayed. | "1" is displayed. | Light at the highest brightness. | Not beep. |
| Step 2-1. Press the trip knob, and hold it: Check each meter | ||||||
| All meters are moved simultaneously in every 0.5 sec. from the lowest position to highest position. Speedometer/Tachometer: Approx. 5 degrees at every movement. Water temperature /Fuel gauge: Moves 1 segment at a time. | Light OFF | Keep the position indicated that set in step 1-2. | Display the current meter directing angle on odometer. Ex.) Displays 135017 when Speedometer/Tachometer: 135 degrees, Water temperature gauge/Fuel gauge: 17 segments. | (Down Arrow) "2" is displayed. | Light at the highest brightness. | Not beep. |
| Step 2-2. Release the trip knob: Specifying the meter directing position | ||||||
| Stop at directing position when the trip knob is released. | Light OFF | Keep the position indicated that set in step 1-2. | Display the current meter directing angle on odometer. | "2" is displayed. | Light at the highest brightness. | Not beep. |
| Step 3-1. Press the trip knob, and hold it: Check illumination | ||||||
| Keep the position that specified at step 2-2. | Light OFF | Varying from the highest brightness (ILL6) to the lowest luminescence (ILL1) every second. After reaching at ILL1, repeat it from ILL6. | Illumination brightness is displayed in the trip meter. (From ILL6 to ILL1) | (Down Arrow) "3" is displayed. | Varying from the highest brightness (ILL6) to the lowest luminescence (ILL1) every second. After reaching at ILL1, repeat it from ILL6. | Not beep. |
| Step 3-2. Release the trip knob: Specifying the illumination brightness | ||||||
| Keep the position that specified at step 2-2. | Light OFF | Keep the brightness at the time when the trip knob is released. | Displays the brightness at the time when the trip knob is released in the trip meter. | "3" is displayed. | Keep the brightness at the time when the trip knob is released. | Not beep. |
| Step 4-1. Press the trip knob: Check the beeping of SPORT shift buzzer (For AT model) | ||||||
| All meter indicator needle returns to lowest position. | Light OFF | Light at the highest brightness. Keep the position indicated that set in step 1-2. | Illumination brightness is displayed in the trip meter. | (Up Arrow And Down Arrow) "8" is displayed. Blinks with buzzer. | Light at the highest brightness. | SPORT shift buzzer beeps. |
| Step 4-2. Press the trip knob: Check the VDC indicator light (Model with VDC) | ||||||
| All meter indicator needle returns to lowest position. | VDC warning light and VDC operation indicator light blink. | Light at the highest brightness. Keep the position indicated that set in step 1-2. | Illumination brightness is displayed in the trip meter. | "4" is displayed. | Light at the highest brightness. | Not beep. |
| Step 5. Press the trip knob: Complete the self-diagnosis 1 cycle | ||||||
| All meter indicator needle returns to lowest position, and go back to step 1 after completion. | ||||||
- Illuminating order table
ILLUMINATING ORDER CHART
| Illuminating order | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | Go back to 1 and repeat |
| Trip meter A/B | AB | A | B | A | B | A | B | A | B | A | B | |
| ODO/trip meter | 8888.8 88888 8 |
00000 00000 0 |
1111.1 11111 1 |
22222 22222 2 |
3333.3 33333 3 |
44444 44444 4 |
5555.5 55555 5 |
66666 66666 6 |
7777.7 77777 7 |
88888 88888 8 |
9999.9 99999 9 |
|
| SPORT shift indicator | 8 | 1 | 2 | 3 | 4 | 5 | E | P | R | N | D | |
| Up Arrow And Down Arrow | Up Arrow And Down Arrow | Up Arrow | Down Arrow | Up Arrow | Down Arrow | Up Arrow | Down Arrow | Up Arrow | Down Arrow | Up Arrow | Down Arrow | |
| Display time (sec.) | 1 | 0.5 | 0.5 | 0.5 | 0.5 | 0.5 | 0.5 | 0.5 | 0.5 | 0.5 | 0.5 |