LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2006 >> Legacy GT spec.B >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 16 (Automatic Transmission (Diagnostics) 4AT) >> Diagnostic Procedure with Diagnostic Trouble Code (DTC) >> DTC P1709 Throttle Position Sensor Circuit High Input

DTC P1709 Throttle Position Sensor Circuit High Input

WARNING: This page is about a different variant/trim than selected.

DTC DETECTING CONDITION: 

The input signal circuit of accelerator pedal position sensor is shorted.

TROUBLE SYMPTOM: 

WIRING DIAGRAM: 

Fig 1: Accelerator Pedal Position Sensor - Wiring Diagram
G05019790
RESISTANCE CHART

Step Check Yes No
1 CHECK ENGINE GROUND TERMINALS.  Is the engine ground terminals tightened securely? Go to step 2.  Tighten the engine ground terminals.
2 CHECK GROUND CIRCUIT FOR ECM. 
  1. Turn the ignition switch to OFF.
  2. Disconnect the connectors from ECM.
  3. Measure the resistance of harness between ECM and engine ground.

    Connector & terminal 

    (B134) No. 5 - Engine ground: 

    (B136) No. 15 - Engine ground: 

    (B137) No. 1 - Engine ground: 

    (B137) No. 2 - Engine ground: 

    (B137) No. 3 - Engine ground: 

    (B137) No. 7 - Engine ground: 

 Is the resistance less than 5 Ω? Go to step 3.  Repair the open circuit of harness between ECM connector and engine grounding terminal.
3 CHECK ACCELERATOR PEDAL POSITION SENSOR. 
  1. Disconnect the connectors from accelerator pedal position sensor.
  2. Measure the resistance between accelerator pedal position sensor connector receptacle's terminals.

    Connector & terminal 

    No. 1 - No. 2: 

 Is the resistance between 0.75 - 3.15 kΩ? Go to step 4.  Replace the accelerator pedal position sensor.
4 CHECK ACCELERATOR PEDAL POSITION SENSOR. 
Measure the resistance between accelerator pedal position sensor connector receptacle's terminals.
Connector & terminal 
No. 2 - No. 3: 		 Is the resistance between 0.15 - 1.05 kΩ? Go to step 5.  Replace the accelerator pedal position sensor.
5 CHECK HARNESS CONNECTOR BETWEEN TCM AND ACCELERATOR PEDAL POSITION SENSOR. 
  1. Disconnect the connector from TCM.
  2. Measure the resistance of the harness between TCM connector and chassis ground.

    Connector & terminal 

    (B54) No. 19 - Chassis ground: 

 Is the resistance more than 1 MΩ? Go to step 6.  Repair the short circuit of harness between TCM and accelerator pedal position sensor connector.
6 CHECK HARNESS CONNECTOR BETWEEN ECM AND ACCELERATOR PEDAL POSITION SENSOR. 
  1. Remove the connectors from ECM.
  2. Measure the resistance of harness between ECM connector and accelerator pedal position sensor connector.

    Connector & terminal 

    (B315) No. 2 - (B135) No. 30: 

 Is the resistance less than 1 Ω? Go to step 7.  Repair the open circuit of harness between ECM and accelerator pedal position sensor.
7 CHECK INPUT SIGNAL FOR TCM USING SUBARU SELECT MONITOR. 
  1. Connect the connectors to TCM, accelerator pedal position sensor, and ECM.
  2. Connect the Subaru Select Monitor to the data link connector.
  3. Turn the ignition switch to ON (engine OFF).
  4. Turn the Subaru Select Monitor switch to ON.
  5. Fully open the throttle.
  6. Read the data of 'Throttle Sensor Voltage" using Subaru Select Monitor.

  • Accelerator pedal position sensor input signal is indicated.
 Is the voltage less than 4.6 V? Go to step 8.  Even if the SPORT indicator light is blinking, the circuit is in normal condition at this time. A temporary poor contact of connector or harness may be the cause. Repair the harness or connector in accelerator pedal position sensor circuit.
8 CHECK POOR CONTACT.  Is there poor contact in accelerator pedal position sensor circuit? Repair the poor contact. Replace the TCM. < Ref. to TRANSMISSION CONTROL MODULE (TCM) . >
scientia non olet · About LEMON Manuals