LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2006 >> Legacy GT spec.B >> Repair and Diagnosis >> External Pages >> Different car >> Section 63 (Engine Controls - Engine (Diagnostics) (H6DO)) >> Diagnostic Procedure with Diagnostic Trouble Code (DTC) >> DTC P0057 Ho2S Heater Control Circuit Low (Bank 2 Sensor 2)

DTC P0057 Ho2S Heater Control Circuit Low (Bank 2 Sensor 2)

WARNING: This page is about a different car, the 2006 Subaru Outback. However, it is still accessible from the selected car via links, so may be relevant.

DTC DETECTING CONDITION: 

CAUTION: After repair or replacement of faulty parts, perform Clear Memory Mode < Ref. to OPERATION , Clear Memory Mode. > and Inspection Mode < Ref. to PROCEDURE , Inspection Mode. >.

WIRING DIAGRAM: 

Fig 1: Rear Oxygen Sensor - Wiring Diagram
G05019030
DTC P0057 HO2S HEATER CONTROL CIRCUIT LOW (BANK 2 SENSOR 2) - DIAGNOSTIC PROCEDURE

Step Check Yes No
1 CHECK POWER SUPPLY TO REAR OXYGEN SENSOR. 
  1. Turn the ignition switch to OFF.
  2. Disconnect the connector from the rear oxygen sensor.
  3. Turn the ignition switch to ON.
  4. Measure the voltage between rear oxygen sensor connector and chassis ground.

    Connector & terminal 

    (E25) No. 2 (+) - Chassis ground (-): 

 Is the voltage more than 10 V? Go to step 2.  Repair the power supply line.
NOTE: In this case, repair the following item:
  • Open circuit in harness between main relay and rear oxygen sensor connector
  • Poor contact of the rear oxygen sensor connector
  • Poor contact in coupling connector
2 CHECK GROUND CIRCUIT FOR ECM. 
  1. Turn the ignition switch to OFF.
  2. Disconnect the connectors from ECM.
  3. Measure the resistance of harness between ECM connector and chassis ground.

    Connector & terminal 

    (B134) No. 3 - Chassis ground: 

    (B134) No. 5 - Chassis ground: 

    (B137) No. 1 - Chassis ground: 

    (B137) No. 2 - Chassis ground: 

    (B137) No. 3 - Chassis ground: 

    (B137) No. 7 - Chassis ground: 

 Is the resistance less than 5 Ω? Go to step 3.  Repair the harness and connector.
NOTE: In this case, repair the following item:
  • Open circuit in harness between ECM and engine ground terminal
  • Poor contact in ECM connector
  • Poor contact in coupling connector
3 CHECK CURRENT DATA. 
  1. Start the engine.
  2. Read the data of rear oxygen sensor heater current using the Subaru Select Monitor or general scan tool.
NOTE:
  • Subaru Select Monitor

    For detailed operation procedure, refer to "READ CURRENT DATA FOR ENGINE". < Ref. to SUBARU SELECT MONITOR . >

  • General scan tool

    For detailed operation procedures, refer to the "General Scan Tool Instruction Manual".

 Is the current more than 0.2 A? Repair the connector.
NOTE: In this case, repair the following item:
  • Poor contact in rear oxygen sensor connector
  • Poor contact in coupling connector
  • Poor contact in ECM connector
 Go to step 4. 
4 CHECK OUTPUT SIGNAL OF ECM. 
  1. Start and idle the engine.
  2. Measure the voltage between ECM connector and chassis ground.

    Connector & terminal 

    (B136) No. 5 (+) - Chassis ground (-): 

 Is the voltage less than 1 V? Go to step 7.  Go to step 5. 
5 CHECK OUTPUT SIGNAL OF ECM. 
Measure the voltage between ECM connector and chassis ground.
Connector & terminal 
(B136) No. 5 (+) - Chassis ground (-): 		 Does the voltage change by shaking the ECM harness and connector while monitoring the value of voltage meter? Repair the poor contact of ECM connector. Go to step 6. 
6 CHECK OUTPUT SIGNAL OF ECM. 
  1. Disconnect the connector from rear oxygen sensor.
  2. Measure the voltage between ECM connector and chassis ground.

    Connector & terminal 

    (B136) No. 5 (+) - Chassis ground (-): 

 Is the voltage less than 1 V? Replace the ECM. < Ref. to ENGINE CONTROL MODULE (ECM) . > Repair the battery short circuit of harness between ECM and rear oxygen sensor connector. After repair, replace the ECM. < Ref. to ENGINE CONTROL MODULE (ECM) . >
7 CHECK REAR OXYGEN SENSOR. 
  1. Turn the ignition switch to OFF.
  2. Measure the resistance between the rear oxygen sensor connector terminals.

    Terminals No. 1-NO.2: 

 Is the resistance less than 30 Ω Repair the harness and connector.
NOTE: In this case, repair the following item:
  • Open circuit in harness between rear oxygen sensor and ECM connector
  • Poor contact in rear oxygen sensor connector
  • Poor contact in ECM connector
  • Poor contact in coupling connector
 Replace the rear oxygen sensor. < Ref. to REAR OXYGEN SENSOR . >
scientia non olet · About LEMON Manuals