LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2006 >> Baja Turbo, Automatic >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 18 (Manual Transmission And Differential) >> General Description >> Preparation Tool >> Special Tools

Special Tools

WARNING: This page is about a different variant/trim than selected.
SPECIAL TOOLS DESCRIPTION

ILLUSTRATION TOOL NUMBER DESCRIPTION REMARKS
G05003164
 398791700 REMOVER Used for removing and installing spring pin (6 mm).
G05002912
 399411700 ACCENT BALL INSTALLER Used for installing reverse shifter rail arm.
G05002464
 899524100 PULLER SET Used for removing and installing roller bearing (Differential).
  1. PULLER
  2. CAP
G05002914
 399780104 WEIGHT Used for measuring preload on roller bearing.
G05002433
 498077000 REMOVER Used for removing roller bearing of drive pinion shaft.
G05002916
 498077300 CENTER DIFFERENTIAL BEARING REMOVER Used for removing the center differential cover ball bearing.
G05002917
 498147000 DEPTH GAUGE Used for adjusting main shaft axial end play.
G05002441
 498247001 MAGNET BASE
  • Used for measuring backlash between side gear and pinion, and hypoid gear.
  • Used with DIAL GAUGE (498247100).
G05002442
 498247100 DIAL GAUGE
  • Used for measuring backlash between side gear and pinion, and hypoid gear.
  • Used with MAGNET BASE (498247001).
G05002920
 498427100 STOPPER Used for securing the drive pinion shaft assembly and driven gear assembly when removing the drive pinion shaft assembly lock nut.
G05002921
 498937000 TRANSMISSION HOLDER Used for removing and installing transmission main shaft lock nut.
G05002922
 499277100 BUSH 1-2 INSTALLER
  • Used for installing 1st driven gear thrust plate and 1st-2nd driven gear bush.
  • Used for installing roller bearing outer races to differential case.
G05002923
 499277200 INSTALLER Used for press-fitting the 2nd driven gear, roller bearings and 5th driven gear onto the driven shaft.
G05002924
 499757002 INSTALLER
  • Used for installing snap ring (OUT 25) and ball bearing (25 x 26 x 17).
  • Used for installing bearing cone of transfer driven gear (extension core side).
G05002436
 499787000 WRENCH ASSY Used for removing and installing differential side retainer.
G05002926
 499827000 PRESS Used for installing speedometer oil seal when installing speedometer cable to transmission.
G05002927
 499857000 5TH DRIVEN GEAR REMOVER Used for removing 5th driven gear.
G05002928
 499877000 RACE 4-5 INSTALLER
  • Used for installing 4th needle bearing race and ball bearing onto transmission main shaft.
  • Used with REMOVER (899714110).
G05002929
 499917500 DRIVE PINION GAUGE ASSY Used for adjusting drive pinion shim.
G05002930
 499927100 HANDLE Used for fitting transmission main shaft.
G05002931
 499937100 TRANSMISSION STAND SET Stand used for transmission disassembly and assembly.
G05002932
 499987003 SOCKET WRENCH (35) Used for removing and installing driven pinion lock nut and main shaft lock nut.
G05002933
 499987300 SOCKET WRENCH (50) Used for removing and installing driven gear assembly lock nut.
G05002934
 899714110 REMOVER Used for fixing transmission main shaft, drive pinion and rear drive shaft.
G05002935
 899864100 REMOVER Used for removing parts on transmission main shaft and drive pinion.
G05002936
 899884100 HOLDER Used for tightening lock nut on sleeve.
G05002937
 899904100 REMOVER Used for removing and installing straight pin.
G05002938
 899988608 SOCKET WRENCH (27) Used for removing and installing drive pinion lock nut.
G05002462
 398497701 ADAPTER
  • Used for installing roller bearing onto differential case.
  • Used with INSTALLER (499277100).
G05002940
 499587000 INSTALLER Used for installing driven gears to driven shaft.
G05002941
 899824100 PRESS Used for installing speedometer shaft oil seal.
G04990833
 499987100 SOCKET WRENCH (35) Used for removing and installing drive pinion lock nut.
G04990834
 899984103 SOCKET WRENCH (35) Used for removing and installing drive pinion lock nut.
G05002432
 498057300 INSTALLER Used for installing extension oil seal.
G05002439
 498255400 PLATE Used for measuring backlash.
G05002944
 498077400 SYNCHRONIZER CONE REMOVER
  • Used for removing synchronizer cone of main shaft.
  • Used for removing 5th driven gear of drive pinion shaft.
G04990225
 41099AA000 ENGINE SUPPORT BRACKET Used for supporting engine.
  1. Engine support bracket (41099AA010)
  2. Engine support (41099AA020)
G05002431
 398527700 PULLER ASSY Used for removing extension case roller bearing.
G05002461
 28399SA010 FRONT DRIVE SHAFT OIL SEAL PROTECTOR
  • Used for protecting oil seal from scratches while installing front drive shaft.
  • TURBO model
G05002460
 18675AA000 DIFFERENTIAL SIDE OIL SEAL INSTALLER
  • Used for installing differential side retainer oil seal.
  • TURBO model
G05002448
 398643600 GAUGE Used for measuring total end play, extension end play and drive pinion height.
G05002948
 38177700 INSTALLER
  • Used for installing bearing cone of transfer driven gear (transfer case side).
  • Used for installing ball bearing of transfer drive gear.
G04990261
 499797000 INSTALLER
  • Used for installing differential side retainer oil seal.
  • Non-TURBO model
scientia non olet · About LEMON Manuals