Abbreviations In The Painting Sector - Ah98.00-P-9409-01SM
MODEL 450, 451, 452, 453, 454
General abbreviations
AbfG: Waste disposal law
AbfNachwV: Waste Documentation Ordinance
AbwAG: Waste Water Charges Act
AVwV: General Administrative Regulation
ATL: Anodic immersion painting
ATV: Specifications governing waste water handling as set forth in the
German Waste Water Association e.V.
Bar (atmospheres): Measurement of air pressure
BlmSchG Law for the protection against harmful environmental effects of
air pollution, Federal Immissions Law
Two-component polyurethane paint with designation "Desmophen Desmodur" (DD)
DIN German Institute for Standardization
DNA: Committee for German Standards
Elex V Regulations on Electrical Facilities in Potentially Explosive Locations
EPC: Electro powder coating (powder-coating: ETL)
ETL: Electro Dip Coating
GPSG: Technical Working Materials and Consumer Products Act
GefStoffV: Dangerous Substances Directive
GGVS: Hazardous Materials Road Transport Regulations
Impulse limit volume spray for sulfuric acid anodizing
HS: High Solid
KTL: Cathodic Dip Painting
KH: Artificial resin
KS: Plastic
MAK: Maximum Workplace Concentration
MBL: Mercedes-Benz Delivery Instructions
MS: Medium Solid
Administrative Offenses Act (OWiG)
Pigment Volume Concentration (PVK)
Potential hydrogenium concentration of hydrogen ions in a hydrous solution (pH value)
RAL: German Institute for Quality Assurance and Certification e. V
German Noise Act
German Clean Air Act
TRbF: Technical Rules for Flammable Liquids
TRGA Technical rules for hazardous materials
Trg A: Technical Directives for Hazardous Materials
TRGS: Technical Rules for Hazardous Substances
USB: Chief Environmental Officer
UWS: Environmental Protection
Directive on Installations Handling Materials Hazardous To Water (VAwS)
VbF: Directive on Flammable Liquids
Association of German Engineers Guidelines (VDI)
Directive on the Storage of Liquids Harmful to Ground Water (VLwF)
WHG: Water Resources Act
m 1 micrometer=1/1000 mm, unit of measurement of coating thickness
2K Two components
Abbreviations for hazardous materials classes
A I Flash point below 21°C
A II Flash point over 21°C to 55°C
A III Flash point over 55°C to 100°C
Abbreviations for plastics
ABS Acrylonitrile Butadiene Styrene
AMMA Acrylonitrile Methylmethacrylate
BFK Boron Fiber Reinforced Plastic
CA Cellulose Acetate
CAB Cellulose Acetate Butyrate
CFK Carbon Reinforced Plastic
EP Epoxy
FEP Perfluoroethylene propylene
GF Glass fiber
GFK Glass Fiber Reinforced Plastic
HDPE High Density Polyethylene
LDPE Low Density Polyethylene
MF Melamine formaldehyde
PA Polyamide
PBTP Polybutylene Terephthalate
PC Polycarbonate
PE Polyethylene
PEC Chlorinated Polyethylene
PETP Polyethylene Terephthalate
PF Phenolic formaldehyde
PIB Polyisobutylene
PMMA Polymethyl Methacrylate
POM Polyoxymethylene, Polyformaldehyde (a polyacetate)
PP Polypropylene
PP-EPDM Polypropylene ethylene propylene diene copolymer
PP-PMMA Polypropylene Polymethyl Methacrylate
PPO Polyphenylene Oxide
PPS Polyphenylene Sulfide
PSU Polysulfone
PS Polystyrene
PTFE Polytetrafluorethylene
PUR Polyurethane
PVC Polyvinyl Chloride
PVCC Chlorinated Polyvinyl Chloride
PVDC Polyvinylidene Chloride
PVDF Polyvinylidene fluoride
PVF Polyvinylfluoride
RTPU-GF Reinforced Thermoplastic Polyurethane - glass-fiber reinforced PUR polyurethane
SAN Styrene Acrylonitrile
SB Styrene-butadiene
SI Silicone
SMS Styrene Alpha Methylstyrene
UF Carbamide Formaldehyde
UP Unsaturated polyester
VPE Cross Linked Polyethylene