Use of fine polishing paste - AP98.00-P-0638A

WARNING: This page does not describe the selected car, but rather 33 other vehicles, including the 2016 Mercedes-Benz E63 S AMG, 2016 Mercedes-Benz E400, 2016 Mercedes-Benz E350, 2016 Mercedes-Benz E300, and 2016 Mercedes-Benz E250. However, it is still accessible from the selected car via links, so may be relevant.

MODEL ALL with high-gloss varnish paintwork

	Application
1	Wash and dry the vehicle		AP98.00-P-0635-01A
		Car Wash	*BR00.45-Z-1002-04A
		Tar remover	*BR00.45-Z-1020-04A
		Insect remover	*BR00.45-Z-1021-04A
2	Buff out damage locally with a lambskin wheel and fine polishing paste	Guide the polishing machine (buffer) with light pressure and do not tilt over otherwise so-called "buffer swirl" occurs: Buffer swirls from polishing painted surfaces: ↓
		Model 123, 124, 126, 129, 140, 163, 168, 170, 201, 202, 203, 204, 207, 208, 209, 210, 211, 212, 215, 220, 230, 240, 461, 463	AR98.00-P-0750-17A
		Model 164, 251	AR98.00-P-0750-17GZ
		Model 169, 245.2	AR98.00-P-0750-17AK
		Model 171	AR98.00-P-0750-17V
		Model 199	AR98.00-P-0750-17SLR
		Model 216, 221	AR98.00-P-0750-17SX
		Model 219 The rotational speed of the lambs wool disk should be between 1500 RPM and 2000 RPM, otherwise the polishing effect is inadequate. Use cork or rubber backing discs. Take care not to rub through the top coat film. Depending on the damage mode, roughen or grind the affected area beforehand with wet abrasive paper (P2000). In the case of clearcoat paint systems with higher scratch-resistance observe corresponding notes in the Service information: ↓ Service Information: Clearcoat paint systems with higher scratch resistance:	AR98.00-P-0750-17Y
		Model 164, 170, 171, 203, 204, 207, 209, 211, 212, 215, 216, 219, 220, 221, 230, 251, 463	SI98.00-P-0013A
		Polish, silicone free 5 l, DB supply specification 7545.00	*BR00.45-Z-1013-04A
		Gloss preservation, 500 ml, DB supply specification 7551.10	*BR00.45-Z-1014-04A
		Fine polishing paste, polish 1 l, DB supply specification 7543.00	*BR00.45-Z-1015-04A
		Paint cleaner	*BR00.45-Z-1016-04A
		Polish 500 ml	*BR00.45-Z-1036-04A
3	Buff up any visible polishing marks and the entire surface of the part	Using the Moltoprene disc without polishing agent. Buff until the luster of the adjacent surface is reached.
4	Rub off polish residues	After drying, buff up with a polishing wad moistened with water.
4	Rub off polish residues	Polishing wad	*BR00.45-Z-1043-04A
5	Buff up the surface manually with polish and a polishing wad	In order to make polishing work easier, use clean polishing wads or clean polishing cloth while changing them frequently.
		Polish, silicone free 5 l, DB supply specification 7545.00	*BR00.45-Z-1013-04A
		Polishing cloth	*BR00.45-Z-1044-04A
6	Rub off polish residues	After the drying process, a light film is formed on the treated surface. Buff up with a clean polishing wad moistened in water until the surface is clear.
7	Treat the surface with gloss preserver	Gloss preservation protects the paintwork against premature matting.	AP98.00-P-0641A

REPAIR MATERIALS

Number	Designation	Order number
BR00.45-Z-1002-04A	Car Wash	A 001 986 41 71
BR00.45-Z-1013-04A	Polish, silicone free 5 l, DB supply specification 7545.00	A 000 986 45 74
BR00.45-Z-1014-04A	Gloss preservation, 500 ml, DB supply specification 7551.10	A 000 986 44 74
BR00.45-Z-1015-04A	Fine polishing paste, polish 1 l, DB supply specification 7543.00	A 000 986 43 74
BR00.45-Z-1016-04A	Paint cleaner	A 001 986 37 71
BR00.45-Z-1020-04A	Tar remover	A 001 986 40 71
BR00.45-Z-1021-04A	Insect remover	A 001 986 39 71
BR00.45-Z-1036-04A	Polish 500 ml	A 000 986 46 74
BR00.45-Z-1043-04A	Polishing wad	A 000 986 02 62
BR00.45-Z-1044-04A	Polishing cloth	A 000 986 04 62