Cylinder head/cylinder head bolts - BE01.30-P-1000-04B
WARNING: This page does not describe the selected car, but rather 33 other vehicles, including the 2016 Mercedes-Benz E63 S AMG, 2016 Mercedes-Benz E400, 2016 Mercedes-Benz E350, 2016 Mercedes-Benz E300, and 2016 Mercedes-Benz E250. However, it is still accessible from the selected car via links, so may be relevant.
ENGINE 103, 104, 111, 112, 113, 119, 120, 137, 155, 157, 270, 271, 272, 273, 274, 275, 276.9, 277, 278, 279, 285
MODIFICATION NOTES
| 11.4.14 | Value changed: Cylinder head bolt | Engine 279 |
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 103 | Engine 104 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 12 | 12 |
| Length (L) when new | mm | 105 | 160 | ||
| Length (L) | mm | ≤ 108, 4 | ≤ 162, 7 | ||
| - | - | - | |||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" | mm | 89, 9...90, 0 | 135, 9...136, 0 |
| Height | mm | ≥ 89, 5 | ≥ 135, 5 | ||
| - | - | - | |||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | - | - |
| Permissible difference of flatness of contact surface in a transverse direction | mm | - | - | ||
| Peak-to-valley height | μm | - | - | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 111 | Engine 112 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 12 | 11 |
| Length (L) when new | mm | 102 | 141, 5 | ||
| Length (L) | mm | ≤ 105 | ≤ 144, 5 | ||
| For picture, see | - | AR01.30-P-5800-03HA | AR01.30-P-5800-03B | ||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" | mm | 135, 9...136, 0 | 106, 2...106, 3 |
| Height | mm | ≥ 135, 5 | - | ||
| For picture, see | - | AR01.30-P-7162A | - | ||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | 0, 08 | 0, 1 |
| Permissible difference of flatness of contact surface in a transverse direction | mm | 0 | 0, 1 | ||
| Peak-to-valley height | μm | 3/10 | 10 | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 113 | Engine 119 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 11 | 12 |
| Length (L) when new | mm | 141, 5 | 160 | ||
| Length (L) | mm | ≤ 144, 5 | ≤ 162, 7 | ||
| For picture, see | - | AR01.30-P-5800-03B | - | ||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" | mm | - | - |
| Height | mm | - | - | ||
| - | - | - | - | ||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | - | - |
| Permissible difference of flatness of contact surface in a transverse direction | mm | - | - | ||
| Peak-to-valley height | μm | - | - | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | 130, 6...130, 7 |
| Reference dimension "H2" | mm | - | 145, 9...146, 0 | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | 130, 0 |
| Reference dimension "H2" | mm | - | 145, 3 | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 120 | Engine 137 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 12 | 10 |
| Length (L) when new | mm | 168 | 126/162 | ||
| Length (L) | mm | ≤ 171 | ≤ 129/165 | ||
| For picture, see | - | - | AR01.30-P-5800-03L | ||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" | mm | 135, 9...136, 0 | - |
| Height | mm | ≥ 135, 5 | - | ||
| - | - | - | - | ||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | - | 0, 03 |
| Permissible difference of flatness of contact surface in a transverse direction | mm | - | 0, 03 | ||
| Peak-to-valley height | μm | - | 10 | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | 110, 87..110, 95 |
| Reference dimension "H2" | mm | - | - | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 155 | Engine 157, 278 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 11 | 11 |
| Length (L) when new | mm | 175+-0, 5 | 173 | ||
| Length (L) | mm | ≤ 176, 6 | ≤ 174, 5 | ||
| For picture, see | - | AR01.30-P-5800-03B | - | ||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" | mm | 114, 9...115, 1 | - |
| Height | mm | 114, 9...115, 1 | - | ||
| - | - | - | - | ||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | - | - |
| Permissible difference of flatness of contact surface in a transverse direction | mm | - | - | ||
| Peak-to-valley height | μm | - | - | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 270 | Engine 271 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 11 | 10 X 1, 5 |
| Length (L) when new | mm | 163 | 165 | ||
| Length (L) | mm | ≤ 164 | ≤ 167, 5 | ||
| For picture, see | - | - | - | ||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" | mm | - | 114, 9...115, 1 |
| Height | mm | - | 114, 9...115, 1 | ||
| - | - | - | - | ||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | - | 0.07 |
| Permissible difference of flatness of contact surface in a transverse direction | mm | - | 0, 05 | ||
| Peak-to-valley height | μm | - | 10 | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 272 | Engine 273 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 11 | 11 |
| Length (L) when new | mm | 170 | 170 | ||
| Length (L) | mm | ≤ 172 | ≤ 172 | ||
| For picture, see | - | - | - | ||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" | mm | - | - |
| Height | mm | - | - | ||
| - | - | - | - | ||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | - | - |
| Permissible difference of flatness of contact surface in a transverse direction | mm | - | - | ||
| Peak-to-valley height | μm | - | - | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 274 | Engine 276.9 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 11 | 11 |
| Length (L) when new | mm | 163 | 170 | ||
| Length (L) | mm | ≤ 164 | ≤ 172 | ||
| For picture, see | - | - | - | ||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" | mm | - | - |
| Height | mm | - | - | ||
| - | - | - | - | ||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | - | - |
| Permissible difference of flatness of contact surface in a transverse direction | mm | - | - | ||
| Peak-to-valley height | μm | - | - | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 275, 285 | Engine 277 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 10 | 10 |
| Length (L) when new | mm | 132/168, 5 | 168, 5 | ||
| Length (L) | mm | ≤ 133, 5/170 | ≤ 170 | ||
| For picture, see | - | - | - | ||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" | mm | - | - |
| Height | mm | - | - | ||
| - | - | - | - | ||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | 0, 03 | - |
| Permissible difference of flatness of contact surface in a transverse direction | mm | 0, 03 | - | ||
| Peak-to-valley height | μm | 10 | - | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | 110, 87...110, 95 | - |
| Reference dimension "H2" | mm | - | - | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 279 | ||
|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 10 |
| Length (L) when new | mm | 168, 5 | ||
| Length (L) | mm | ≤ 170 | ||
| For picture, see | - | - | ||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" | mm | - |
| Height | mm | - | ||
| - | - | - | ||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | - |
| Permissible difference of flatness of contact surface in a transverse direction | mm | - | ||
| Peak-to-valley height | μm | - | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - |
| Reference dimension "H2" | mm | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - |
| Reference dimension "H2" | mm | - | ||