Remove/install oil separator - AR01.20-P-9750LFD
WARNING: This page does not describe the selected car, but rather 33 other vehicles, including the 2016 Mercedes-Benz E63 S AMG, 2016 Mercedes-Benz E400, 2016 Mercedes-Benz E350, 2016 Mercedes-Benz E300, and 2016 Mercedes-Benz E250. However, it is still accessible from the selected car via links, so may be relevant.
ENGINE 642 in MODEL 207, 212, 218 with CODE 927 (Emission control system with Euro 6 technology)
ENGINE 642 in MODEL 222
| Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | AS00.00-Z-0011-01A | |
| Notes on avoiding damage through contamination and foreign objects | AH00.00-P-5000-01A | ||
| Remove/install | |||
| 1 | Remove engine cover | ||
| 2 | Remove engine air intake duct downstream of air filter | AR09.10-P-8130OGE | |
| 3 | Detach electrical connections (1, 6) from holder and expose | ||
| 4 | Remove screw/bolts (2) on oil separator (4) | *BA01.20-P-1005-01P | |
| 5 | Remove screws/bolts (3) of bleed valve (5) | *BA01.20-P-1006-01P | |
| 6 | Remove oil separator (4) with bleed valve (5) | ||
| 7 | Install in the reverse order | ||
| Check | |||
| 8 | Check oil level and correct if necessary | ||
| ENGINE 642.861 in MODEL 222 The vehicle must stand horizontally on its wheels. This prevents measurement errors. |
AP18.00-P-0101EWO | ||
ENGINE 642.861 with CODE 474 (Particulate trap) |
*BF18.00-P-1001-01S | ||
| Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | AS00.00-Z-0005-01A | |
| 9 | Perform an engine test run and check engine for leaktightness |
CRANKCASE VENTILATION, CYLINDER HEAD COVER
| Number | Designation | ENGINE 642 | |
|---|---|---|---|
| BA01.20-P-1005-01P | Bolt, oil separator/bleed valve to cylinder head cover | Nm | 14 |
CRANKCASE VENTILATION, CYLINDER HEAD COVER
| Number | Designation | ENGINE 642 | |
|---|---|---|---|
| BA01.20-P-1006-01P | Bolt, bleed valve/cover to cylinder head | Nm | 9 |
ENGINE LUBRICATION SYSTEM
| Number | Designation | ENGINE 642.826/830/832/834/835/836/838/850/85 2/853/854/856/858/8 61/862/867/868 with CODE 474 (Particulate trap) | ||
|---|---|---|---|---|
| BF18.00-P-1001-01S | Engine oil | Filling capacity (oil and filter change) | Liter | 8, 0 |
| Specifications | Low SPAsh multigrade service engine oils (specification 228.51). See https://bevo.mercedes-benz.com/index.php?language_id=1 | |||
| Specifications | Low SPAsh multigrade service engine oils (specification 229.31). See https://bevo.mercedes-benz.com/index.php?language_id=1 | |||
| Specifications | Low SPAsh multigrade service engine oils (specification 229.51). See https://bevo.mercedes-benz.com/index.php?language_id=1 | |||
| Specifications | Low SPAsh multigrade service engine oils (specification 229.52). See https://bevo.mercedes-benz.com/index.php?language_id=1 | |||