Remove/install antenna cable - AR82.62-P-1200MCC
MODEL 451.3/4
with CODE (C08) Radio preinstallation incl. rod antenna (FFO)
with CODE (460) Canada version with CODE (494) USA version
with CODE (498) Japan version
Shown on vehicle with code (494) USA version
Fig 1: Identifying Antenna Cable Remove/Install Components - Shown On Vehicle With Code (494) USA Version (1 Of 2)
Fig 2: Identifying Antenna Cable Remove/Install Components - Shown On Vehicle With Code (494) USA Version (2 Of 2)
| Removing | |||
| 1 | Remove left front headlamp unit | * not for USA | AR82.10-P-4730MCC |
| * for USA only | AR82.10-P-4730MCU | ||
| 2 | Remove radio | With code (C50) smart radio 10 or Code (C57) smart radio 9 or Code (516) RADIO WITH USB INTERFACE or code (527) High-Line radio or code (P02) car2go with instrument panel up to production date 30.8.10 * not for USA |
AR82.60-P-7502MCC |
| * for USA only | AR82.60-P-7502MCU | ||
| 3 | Remove antenna cable (1) from antenna base (2) | ||
| 4.1 | Remove antenna cable (1) from body in area of upper door hinge | With code (C08) Radio preinstallation with rod antenna (FFO) and without code (460) Canada version, without code (494) USA version or without code (498) Japan version |
|
| 4.2 | Detach antenna amplifier (3) from body | With code (460) Canada version With code (494) USA version or With code (498) Japan version |
|
| 5 | Remove adhesive tape (4) from protective tube (5) and push protective tube (5) back until main wiring harness is exposed | ||
| 6 | Expose antenna cable (1) at main wiring harness and cut off (arrow A) | ||
| 7 | Expose antenna amplifier supply line (6) at main wiring harness and cut off (arrow A) | With code (460) Canada version With code (494) USA version or With code (498) Japan version |
|
| 8 | Make cable hole at grommet (8) | ||
| 9 | Cut off antenna cable (1) in radio recess (arrow B) | ||
| Install | |||
| 10 | Remove adhesive tape (9) from new antenna cable (1) | ||
| 11.1 | Clip antenna cable (1) into body in area of upper door hinge | With code (C08) Radio preinstallation with rod antenna (FFO) and Without code (460) Canada version, without code (494) USA version or without code (498) Japan version |
|
| 11.2 | Clip antenna amplifier (3) into body | With code (460) Canada version With code (494) USA version or With code (498) Japan version |
|
| 12 | Screw antenna cable (1) onto antenna base (2) by hand | ||
| 13 | Route antenna cable (1) along main wiring harness and guide through grommet (8) into interior | Fig 3 | |
| 14 | Route new antenna amplifier supply line (6.1) along antenna cable (1) to antenna amplifier supply line (6) at main wiring harness | ||
| 15 | Cut new antenna amplifier supply line (6.1) to length and connect to antenna amplifier supply line (6) using solder connector (10) | With code (460) Canada version With code (494) USA version or With code (498) Japan version |
AR00.19-P-0100A |
| 16 | Push protective tube (5) forward and fix in place using suitable insulation tape | ||
| 17 | Fix antenna cable (1) in place at main wiring harness using suitable insulation tape. | ||
| 18 | Route antenna cable (1) along main wiring harness toward radio recess and fasten using cable tie (11) | ||
| 19 | Fix antenna cable (1) in place at main wiring harness in radio recess using suitable insulation tape | ||
| 20 | Seal grommet (8) using suitable sealant | ||
| 21 | Install left front lamp unit | * not for USA | AR82.10-P-4730MCC |
| * for USA only | AR82.10-P-4730MCU | ||
| 22 | Install radio | With code (C50) smart radio 10 or Code (C57) smart radio 9 or Code (516) RADIO WITH USB INTERFACE or code (527) High-Line radio or code (P02) car2go with instrument panel up to production date 30.8.10 * not for USA |
AR82.60-P-7502MCC |
| * for USA only | AR82.60-P-7502MCU |