LEMON Manuals: Even more car manuals for everyone
Home >> Scion >> 2016 >> iA Automatic Trans >> Repair and Diagnosis >> Accessories & Equipment >> Interior/Illumination Lights >> Lighting System (Interior) - Diagnostic Codes (B104187B - B120786) >> Lighting System >> DTC B10A6-64: Main Light Switch signal plausibility failure [07/2015 - ] >> Procedure

DTC B10A6-64: Main Light Switch signal plausibility failure [07/2015 - ]: Procedure

  1. VERIFY MAIN BODY ECU DTCS AGAIN 
    1. Clear the DTC for the main body ECU using the Techstream.

      Refer to DTC CHECK / CLEAR [07/2015 - ]

      Body Electrical > Body Control Module > Clear DTCs 

    2. Switch the ignition ON (engine off or on) and wait for 5 s or more
    3. Retrieve the main body ECU DTCs using the Techstream.

      Refer to DTC CHECK / CLEAR [07/2015 - ]

      Body Electrical > Body Control Module > Trouble Codes 

    4. Is the same DTC displayed?

      Result

      Result
      Yes
      No

    Result:  2

    No 

    See step  5

    Result:  1

    Yes 

    See step  2

  2. VERIFY ENGINE STOP AND START ECU DTCS 
    1. Retrieve the engine stop and start ECU DTCs using the Techstream.

      Refer to DTC CHECK / CLEAR [07/2015 - ]

      Body Electrical > Smart Start Unit > Trouble Codes 

    2. Are any other DTCs displayed?

      Result

      Result
      Yes
      No

    Result:  2

    Yes 

    REPAIR OR REPLACE THE MALFUNCTIONING PART ACCORDING TO THE APPLICABLE DTC TROUBLESHOOTING. 

    1. Refer to DIAGNOSTIC TROUBLE CODE CHART [07/2015 - ]

    Result:  1

    No 

    See step  3

  3. INSPECT HEADLIGHT DIMMER SWITCH 
    1. Inspect the headlight dimmer switch.

      Refer to REMOVAL [07/2015 - ]

    2. Is the headlight dimmer switch normal?

      Result

      Result
      Yes
      No

    Result:  1

    Yes 

    See step  7

    Result:  2

    No 

    See step  8

  4. VERIFY THAT REPAIRS HAVE BEEN COMPLETED 
    1. Clear the DTC for the main body ECU using the Techstream.

      Refer to DTC CHECK / CLEAR [07/2015 - ]

      Body Electrical > Body Control Module > Clear DTCs 

    2. Switch the ignition ON (engine off or on) and wait for 5 s or more.
    3. Retrieve the main body ECU DTCs using the Techstream.

      Refer to DTC CHECK / CLEAR [07/2015 - ]

      Body Electrical > Body Control Module > Trouble Codes 

    4. Is the same DTC displayed?

      Result

      Result
      Yes
      No

    Result:  2

    Yes 

    See step  6

    Result:  1

    No 

    See step  5

  5. VERIFY IF OTHER DTCS DISPLAYED 
    1. Are any other DTCs displayed?

      Result

      Result
      Yes
      No

    Result:  1

    Yes 

    REPAIR OR REPLACE THE MALFUNCTIONING PART ACCORDING TO THE APPLICABLE DTC TROUBLESHOOTING. 

    1. Refer to DTC CHECK / CLEAR [07/2015 - ]

    Result:  2

    No 

    DTC TROUBLESHOOTING COMPLETED 

  6. REPLACE THE MAIN BODY ECU, THEN GO TO THE NEXT STEP. 
    1. Refer to REMOVAL [07/2015 - ]

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  5

  7. REPLACE THE ENGINE STOP AND START ECU, THEN GO TO THE NEXT STEP. 
    1. Refer to SYSTEM DIAGRAM [07/2015 - ]

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  4

  8. REPLACE THE HEADLIGHT DIMMER SWITCH, THEN GO TO THE NEXT STEP. 
    1. Refer to REMOVAL [07/2015 - ]

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  4