DTC B10A0-64: Wiper/ Washer Switch signal plausibility failure [07/2015 - ]: Procedure

VERIFY MAIN BODY ECU DTCS AGAIN

Clear the DTC for the main body ECU using the Techstream.
Refer to DTC CHECK / CLEAR [07/2015 - ]

Body Electrical > Body Control Module > Clear DTCs
Switch the ignition ON (engine off or on) and wait for 5 s or more.
Retrieve the main body ECU DTCs using the Techstream.
Refer to DTC CHECK / CLEAR [07/2015 - ]

Body Electrical > Body Control Module > Trouble Codes

Is the same DTC displayed?

Result

Result
Yes
No

Result: 2

See step 6

Result: 1

Yes

See step 2

DETERMINE MALFUNCTIONING LOCATION BY PERFORMING PID/DATA MONITOR INSPECTION

Using the Techstream, display the following PIDs for the engine stop and start ECU.

Refer to DATA LIST / ACTIVE TEST [07/2015 - ]

Front Washer Switch
Rear Washer Switch
Front Wiper Switch (INT)
Front Wiper Switch (LOW)
Rear Wiper Switch (INT)
Rear Wiper Switch (ON)

Body Electrical > Smart Start Unit > Data List

Tester Display
Front Washer Switch
Rear Washer Switch
Front Wiper Switch (INT)
Front Wiper Switch (LOW)
Rear Wiper Switch (INT)
Rear Wiper Switch (ON)

Does the PID monitoring value switch correctly according to the wiper switch operation?

Result

Result
Yes
No

Result: 2

Yes

See step 12

Result: 1

See step 3

INSPECT WIPER SWITCH

Inspect the wiper switch.
Refer to INSPECTION [07/2015 - ]

Is the wiper switch normal?

Result

Result
Yes
No

Result: 1

Yes

See step 10

Result: 2

See step 11

DETERMINE MALFUNCTIONING LOCATION BY PERFORMING PID/DATA MONITOR INSPECTION

Using the Techstream, display the following PIDs for the main body ECU.

Refer to DATA LIST / ACTIVE TEST [07/2015 - ]

Front Wiper Switch
Rear Wiper Switch

Body Electrical > Body Control Module > Data List

Tester Display
Front Wiper Switch
Rear Wiper Switch

Does the PID monitoring value switch correctly according to the wiper switch operation?

Result

Result
Yes
No

Result: 1

Yes

See step 8

Result: 2

See step 9

VERIFY THAT REPAIRS HAVE BEEN COMPLETED

Clear the DTC for the main body ECU using the Techstream.
Refer to DTC CHECK / CLEAR [07/2015 - ]

Body Electrical > Body Control Module > Clear DTCs
Switch the ignition ON (engine off or on) and wait for 5 s or more.
Retrieve the main body ECU DTCs using the Techstream.
Refer to DTC CHECK / CLEAR [07/2015 - ]

Body Electrical > Body Control Module > Trouble Codes

Is the same DTC displayed?

Result

Result
Yes
No

Result: 2

Yes

See step 7

Result: 1

See step 6

VERIFY IF OTHER DTCS DISPLAYED

Are any other DTCs displayed?

Result

Result
Yes
No

Result: 1

Yes

REPAIR OR REPLACE THE MALFUNCTIONING PART ACCORDING TO THE APPLICABLE DTC TROUBLESHOOTING.

Refer to DIAGNOSTIC TROUBLE CODE CHART [07/2015 - ]

Result: 2

DTC TROUBLESHOOTING COMPLETED.

REPEAT THE INSPECTION FROM STEP 1.

If the malfunction recurs, replace the main body ECU.
Refer to REMOVAL [07/2015 - ]

Go to the next step

Result

Proceed to
NEXT

Result: 1

See step 6

GO TO THE NEXT STEP.

(Circuit between engine stop and start ECU and main body ECU is normal.)

Result

Proceed to
NEXT

Result: 1

See step 5

REPLACE THE ENGINE STOP AND START ECU, THEN GO TO THE NEXT STEP.

Refer to REMOVAL [07/2015 - ]

Result

Proceed to
NEXT

Result: 1

See step 5

REPLACE THE ENGINE STOP AND START ECU, THEN GO TO STEP 5.

Refer to REMOVAL [07/2015 - ]

Result

Proceed to
NEXT

Result: 1

See step 5

REPLACE THE WIPER SWITCH, THEN GO TO STEP 5.

Refer to REMOVAL [07/2015 - ]

Result

Proceed to
NEXT

Result: 1

See step 5

GO TO STEP 4. (CIRCUIT BETWEEN WIPER SWITCH AND ENGINE STOP AND START ECU IS NORMAL)
Result

Proceed to

NEXT

Result: 1

NEXT

See step 4