DTC U2013-13: Switch Pack circuit open [07/2015 - ]: Procedure

INSPECT CLUSTER SWITCH CONNECTOR CONDITION

Switch the ignition off.
Disconnect the negative battery cable.
Refer to REMOVAL [07/2015 - ]
Disconnect the cluster switch connector.
Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.

Is the connector normal?

Result

Proceed to
Yes
No

Result: 1

See step 11

Result: 2

Yes

See step 2

INSPECT COMBINATION METER CONNECTOR CONDITION

Disconnect the combination meter connector.
Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.

Is the connector normal?

Result

Proceed to
Yes
No

Result: 1

See step 10

Result: 2

Yes

See step 3

INSPECT CLUSTER SWITCH CIRCUIT FOR OPEN CIRCUIT

Verify that the cluster switch and combination meter connectors are disconnected.
Inspect for continuity between the following terminals (wiring harness-side):
1. Combination meter terminal D55-23 - Cluster switch terminal D57-6
2. Combination meter terminal D55-1 - Cluster switch terminal D57-2

Is there continuity?

Result

Proceed to
Yes
No

Result: 2

See step 9

Result: 1

Yes

See step 4

INSPECT CLUSTER SWITCH

Inspect the cluster switch.
Refer to INSPECTION [07/2015 - ]

Refer to INSPECTION [07/2015 - ]

Refer to INSPECTION [07/2015 - ]

Is the cluster switch normal?

Result

Proceed to
Yes
No

Result: 1

See step 8

Result: 2

Yes

See step 5

VERIFY THAT REPAIRS HAVE BEEN COMPLETED

Always reconnect all disconnected connectors.
Connect the negative battery cable.
Refer to REMOVAL [07/2015 - ]
Clear the DTC for the combination meter using the Techstream.
Refer to DTC CHECK / CLEAR [07/2015 - ]

Body Electrical > Instrument Cluster > Clear DTCs
Switch the ignition ON (engine off or on) and wait for 5 s or more.
Retrieve the combination meter DTCs using the Techstream.
Refer to DTC CHECK / CLEAR [07/2015 - ]

Body Electrical > Instrument Cluster > Trouble Codes

Is the same DTC displayed?

Result

Proceed to
Yes
No

Result: 2

Yes

See step 7

Result: 1

See step 6

VERIFY IF OTHER DTCs DISPLAYED

Are any other DTCs displayed?

Result

Proceed to
Yes
No

Result: 1

DTC TROUBLESHOOTING COMPLETED.

Result: 2

Yes

REPAIR OR REPLACE THE MALFUNCTIONING PART ACCORDING TO THE APPLICABLE DTC TROUBLESHOOTING. Refer to DIAGNOSTIC TROUBLE CODE CHART [07/2015 - ]

REPEAT THE INSPECTION FROM STEP 1.

If the malfunction recurs, replace the combination meter.
Refer to REMOVAL [07/2015 - ]

Go to the next step.

Result

Proceed to
NEXT

Result: 1

See step 6

REPLACE THE CLUSTER SWITCH.

Refer to REMOVAL [07/2015 - ]

Then go to the next step.

Result

Proceed to
NEXT

Result: 1

See step 5

REFER TO THE WIRING DIAGRAM AND VERIFY WHETHER OR NOT THERE IS A COMMON CONNECTOR BETWEEN THE FOLLOWING TERMINALS:

Combination meter terminal D55-23 - Cluster switch terminal D57-6
Combination meter terminal D55-1 - Cluster switch terminal D57-2

If there is a common connector:

Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.
Repair or replace the malfunctioning part.

If there is no common connector:

Repair or replace the wiring harness which has an open circuit.

Go to the next step.

Result

Proceed to
NEXT

Result: 1

See step 5

REPAIR OR REPLACE THE CONNECTOR.

Then go to the next step.

Result

Proceed to
NEXT

Result: 1

See step 5

REPAIR OR REPLACE THE CONNECTOR.

Then go to the next step.

Result

Proceed to
NEXT

Result: 1

See step 5