DTC U0433-00: Invalid Data Received From Image Processing Module A [07/2015 - ]: Procedure

VERIFY ALL SYSTEM DTCs

Switch the ignition off.
Switch the ignition ON (engine off or on) and wait for 10 s or more.
Perform a CMDTC self-test using the Techstream.
Refer to DTC CHECK / CLEAR [07/2015 - ]

Body Electrical > Instrument Cluster > Trouble Codes

Are any DTCs other than DTC U043300 displayed?

Result

Proceed to
Yes
No

Result: 1

Yes

REPAIR OR REPLACE THE MALFUNCTIONING PART ACCORDING TO THE APPLICABLE DTC TROUBLESHOOTING.

Refer to DIAGNOSTIC TROUBLE CODE CHART [07/2015 - ]
Refer to DIAGNOSTIC TROUBLE CODE CHART [07/2015 - ]
Refer to DIAGNOSTIC TROUBLE CODE CHART [07/2015 - ]
Refer to DIAGNOSTIC TROUBLE CODE CHART [07/2015 - ]

Result: 2

See step 2

VERIFY DTCs AGAIN

Clear the DTC for the combination meter using the Techstream.
Refer to DTC CHECK / CLEAR [07/2015 - ]

Body Electrical > Instrument Cluster > Clear DTCs
Switch the ignition ON (engine off or on) and wait for 10 s or more.
Perform a CMDTC self-test using the Techstream.
Refer to DTC CHECK / CLEAR [07/2015 - ]

Body Electrical > Instrument Cluster > Trouble Codes

Is the same DTC displayed?

Result

Proceed to
Yes
No

Result: 1

See step 6

Result: 2

Yes

See step 3

VERIFY MULTI-DISPLAY

Verify the multi-display.

Is the "PCS Clean front windshield glass" displayed in the multi-display?

Result

Proceed to
Yes
No

Result: 2

Yes

See step 9

Result: 1

See step 5

VERIFY IF MALFUNCTIONING LOCATION IS LASER SENSOR DEPENDING ON REPEATABILITY

Clear the DTC for the combination meter using the Techstream.
Refer to DTC CHECK / CLEAR [07/2015 - ]

Body Electrical > Instrument Cluster > Clear DTCs
Switch the ignition ON (engine off or on) and wait for 10 s or more.
Perform a CMDTC self-test using the Techstream.
Refer to DTC CHECK / CLEAR [07/2015 - ]

Body Electrical > Instrument Cluster > Trouble Codes

Is the same DTC displayed?

Result

Proceed to
Yes
No

Result: 2

Yes

See step 8

Result: 1

See step 6

VERIFY THAT REPAIRS HAVE BEEN COMPLETED

Clear the DTC for the combination meter using the Techstream.
Refer to DTC CHECK / CLEAR [07/2015 - ]

Body Electrical > Instrument Cluster > Clear DTCs
Switch the ignition ON (engine off or on) and wait for 10 s or more.
Perform a CMDTC self-test using the Techstream.
Refer to DTC CHECK / CLEAR [07/2015 - ]

Body Electrical > Instrument Cluster > Trouble Codes

Is the same DTC displayed?

Result

Proceed to
Yes
No

Result: 2

Yes

See step 7

Result: 1

See step 6

VERIFY IF OTHER DTCs DISPLAYED

Are any other DTCs displayed?

Result

Proceed to
Yes
No

Result: 1

DTC TROUBLESHOOTING COMPLETED.

Result: 2

Yes

REPAIR OR REPLACE THE MALFUNCTIONING PART ACCORDING TO THE APPLICABLE DTC TROUBLESHOOTING. Refer to DIAGNOSTIC TROUBLE CODE CHART [07/2015 - ]

REPLACE THE COMBINATION METER.

Refer to REMOVAL [07/2015 - ]

Then go to the next step.

Result

Proceed to
NEXT

Result: 1

See step 6

REPLACE THE LASER SENSOR.

Refer to REMOVAL [07/2015 - ]

Then go to the next step.

Result

Proceed to
NEXT

Result: 1

See step 5

CLEAN THE WINDSHIELD GLASS.

Then go to the next step.

Result

Proceed to
NEXT

Result: 1

See step 4