LEMON Manuals: Even more car manuals for everyone
Home >> Scion >> 2016 >> iA Automatic Trans >> Repair and Diagnosis >> Accessories & Equipment >> Exterior Lights >> Lighting System (Exterior) - Diagnostic Codes (B121911 - B1D3586) >> Lighting System >> DTC B1D02-11: Left High Beam Circuit circuit short to ground [07/2015 - ] >> Procedure

DTC B1D02-11: Left High Beam Circuit circuit short to ground [07/2015 - ]: Procedure

  1. INSPECT POWER SOURCE CONTROL (POWER MANAGEMENT CONTROL ECU) CONNECTOR CONDITION 
    1. Switch the ignition off.
    2. Disconnect the negative battery cable.

      Refer to REMOVAL [07/2015 - ]

    3. Disconnect the power source control (power management control ECU) connector.
    4. Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
    5. Is the connector normal?

      Result

      Result Proceed to
      With headlight assembly (bulb type) Yes (A)
      With headlight assembly (LED type) Yes (B)
      - No

    Result:  1

    Yes (A) 

    See step  15

    Result:  2

    Yes (B) 

    See step  16

    Result:  3

    No 

    See step  17

  2. VISUALLY INSPECT HEADLIGHT HI/LO BULB (LH) 
    1. Visually inspect the headlight HI/LO bulb (LH).
    2. Is the headlight HI/LO bulb (LH) normal?

      Result

      Result
      Yes
      No

    Result:  2

    No 

    See step  14

    Result:  1

    Yes 

    See step  3

  3. INSPECT HEADLIGHT ASSEMBLY (LH) CONNECTOR CONDITION 
    1. Disconnect the headlight assembly (LH) connector.
    2. Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
    3. Is the connector normal?

      Result

      Result
      Yes
      No

    Result:  2

    No 

    See step  13

    Result:  1

    Yes 

    See step  4

  4. INSPECT HEADLIGHT HI (LH) CONTROL CIRCUIT FOR SHORT TO GROUND 
    1. Verify that the headlight assembly (LH) and power source control (power management control ECU) connectors are disconnected.
    2. Inspect for continuity between headlight assembly (LH) terminal A24-1 (bulb type), A23-1 (LED type) (wiring harness-side) and body ground.
    3. Is there continuity?

      Result

      Result Proceed to
      - Yes
      With headlight assembly (bulb type) No (A)
      With headlight assembly (LED type) No (B)

    Result:  1

    Yes 

    See step  10

    Result:  3

    No (A) 

    See step  11

    Result:  2

    No (B) 

    See step  12

  5. VERIFY IF MALFUNCTIONING LOCATION IS HEADLIGHT ASSEMBLY (LH) DEPENDING ON REPEATABILITY 
    1. Always reconnect all disconnected connectors.
    2. Connect the negative battery cable.

      Refer to REMOVAL [07/2015 - ]

    3. Clear the DTC for the power source control (power management control ECU) using the Techstream.

      Refer to DTC CHECK / CLEAR [07/2015 - ]

      Body Electrical > Electric Supply Unit > Clear DTCs 

    4. Operate the headlight dimmer switch to the HEAD position and the dimmer switch to HI position.
    5. Retrieve the power source control (power management control ECU) DTCs using the Techstream.

      Refer to DTC CHECK / CLEAR [07/2015 - ]

      Body Electrical > Electric Supply Unit > Trouble Codes 

    6. Is the same DTC displayed?

      Result

      Result
      Yes
      No

    Result:  1

    No 

    See step  7

    Result:  2

    Yes 

    See step  9

  6. VERIFY THAT REPAIRS HAVE BEEN COMPLETED 
    1. Always reconnect all disconnected connectors.
    2. Connect the negative battery cable.

      Refer to REMOVAL [07/2015 - ]

    3. Clear the DTC for the power source control (power management control ECU) using the Techstream.

      Refer to DTC CHECK / CLEAR [07/2015 - ]

      Body Electrical > Electric Supply Unit > Clear DTCs 

    4. Operate the headlight dimmer switch to the HEAD position and the dimmer switch to HI position.
    5. Retrieve the power source control (power management control ECU) DTCs using the Techstream.

      Refer to DTC CHECK / CLEAR [07/2015 - ]

      Body Electrical > Electric Supply Unit > Trouble Codes 

    6. Is the same DTC displayed?

      Result

      Result
      Yes
      No

    Result:  2

    Yes 

    See step  8

    Result:  1

    No 

    See step  7

  7. VERIFY IF OTHER DTCS DISPLAYED 
    1. Are any other DTCs displayed?

      Result

      Result
      Yes
      No

    Result:  1

    No 

    DTC TROUBLESHOOTING COMPLETED. 

    Result:  2

    Yes 

    REPAIR OR REPLACE THE MALFUNCTIONING PART ACCORDING TO THE APPLICABLE DTC TROUBLESHOOTING. 

    1. Refer to DIAGNOSTIC TROUBLE CODE CHART [07/2015 - ]
  8. REPEAT THE INSPECTION FROM STEP 1. 
    1. If the malfunction recurs, replace the power source control (power management control ECU).

      Refer to REMOVAL [07/2015 - ]

    2. Go to the next step.

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  7

  9. REPLACE THE HEADLIGHT ASSEMBLY (LH). 
    1. Refer to REMOVAL [07/2015 - ]
    2. Then go to the next step.

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  6

  10. REFER TO THE WIRING DIAGRAM AND VERIFY WHETHER OR NOT THERE IS A COMMON CONNECTOR BETWEEN HEADLIGHT ASSEMBLY (LH) AND POWER SOURCE CONTROL (POWER MANAGEMENT CONTROL ECU). 
    1. Refer to the wiring diagram and verify whether or not there is a common connector between headlight assembly (LH) terminal A24-1 (bulb type), A23-1 (LED type) and power source control (power management control ECU) terminal A27-1.

      If there is a common connector: 

      1. Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.
      2. Repair or replace the malfunctioning part.

      If there is no common connector: 

      1. Repair or replace the wiring harness which has a short to ground.
    2. Go to the next step.

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  6

  11. WITH FRONT HEADLIGHT ASSEMBLY (BULB TYPE) 
    1. Go to the next step.

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  6

  12. WITH HEADLIGHT ASSEMBLY (LED TYPE) 
    1. Go to the next step.

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  5

  13. REPAIR OR REPLACE THE CONNECTOR. 
    1. Then go to the next step.

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  6

  14. REPLACE THE HEADLIGHT HI/LO BULB (LH). 
    1. Refer to REPLACEMENT [07/2015 - ]
    2. Then go to the next step.

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  6

  15. WITH HEADLIGHT ASSEMBLY (BULB TYPE) 
    1. Go to the next step.

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  2

  16. WITH HEADLIGHT ASSEMBLY (LED TYPE) 
    1. Go to the next step.

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  3

  17. REPAIR OR REPLACE THE CONNECTOR. 
    1. Then go to the next step.

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  6

scientia non olet · About LEMON Manuals