LEMON Manuals: Even more car manuals for everyone
Home >> Scion >> 2014 >> FR-S Standard Trans >> Repair and Diagnosis (Single Page) >> Restraints >> Air Bag, SRS >> Supplemental Restraint System (Diagnostic Codes & Symptom Tests) >> Airbag System >> DTC B1612: Front Airbag Sensor RH Lost Communication; DTC B1613: Front Airbag Sensor RH Initialization >> Procedure

DTC B1612: Front Airbag Sensor RH Lost Communication; DTC B1613: Front Airbag Sensor RH Initialization: Procedure

  1. CHECK CONNECTORS 
    1. Turn the ignition switch off.
    2. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag ECU assembly and front airbag sensor RH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

      OK

      The connectors are properly connected.

      HINT: 

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag ECU assembly and front airbag sensor RH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.
    5. Check that the terminals of the connectors are not damaged.

      OK

      The terminals are not deformed or damaged.

    NG → REPLACE WIRE HARNESS 

    OK: Go to next step 

  2. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN) 
    1. Connect the connectors that link the engine room main wire and instrument panel wire.
      GTY387960Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.
      NOTE:

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A51-2 (BUSIN) - A51-1 (RTNIN) Always Below 1 Ω
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag ECU Assembly
      *3 Service Wire
      *a Front view of wire harness connector
      (to Airbag ECU Assembly)
      *b Front view of wire harness connector
      (to Front Airbag Sensor RH)

    NG → See step   7 

    OK: Go to next step 

  3. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT) 
    1. Disconnect the service wire from connector B.
      GTY388145Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A51-2 (BUSIN) - A51-1 (RTNIN) Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag ECU Assembly
      *a Front view of wire harness connector
      (to Front Airbag Sensor RH)

    NG → See step   8 

    OK: Go to next step 

  4. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO B+) 
    1. Connect the cable to the negative (-) battery terminal.
      GTY388145Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Turn the ignition switch to ON.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      A51-2 (BUSIN) - Body ground Ignition switch ON Below 1 V
      A51-1 (RTNIN) - Body ground Ignition switch ON Below 1 V
    4. Turn the ignition switch off.
    5. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag ECU Assembly
      *a Front view of wire harness connector
      (to Front Airbag Sensor RH)

    NG → See step   9 

    OK: Go to next step 

  5. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY388145Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      A51-2 (BUSIN) - Body ground Always 1 MΩ or higher
      A51-1 (RTNIN) - Body ground Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag ECU Assembly
      *a Front view of wire harness connector
      (to Front Airbag Sensor RH)

    NG → See step   10 

    OK: Go to next step 

  6. CHECK FRONT AIRBAG SENSOR RH 
    1. Connect the connector to the airbag ECU assembly.
      GTY320490Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Interchange the front airbag sensor RH with LH and connect the connectors.
    3. Connect the cable to the negative (-) battery terminal.
    4. Clear the DTCs stored in memory. Refer to DTC CHECK / CLEAR [07/2013 - ] .
    5. Turn the ignition switch off.
    6. Turn the ignition switch to ON, and wait for at least 60 seconds.
    7. Check for DTCs. Refer to DTC CHECK / CLEAR [07/2013 - ] .

      Result

      Result Proceed to
      DTCs B1612, B1613, B1617 and B1618 are not output. A
      DTC B1617 or B1618 is output. B
      DTC B1612 or B1613 is output. C

      HINT: 

      Codes other than DTCs B1612, B1613, B1617 and B1618 may be output at this time, but they are not related to this check.

    8. Turn the ignition switch off.
    9. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    10. Return the front airbag sensor RH and LH to their original positions and connect the connectors.
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor LH
      *2 Airbag ECU Assembly

    B → See step   13 

    C → See step   12 

    A → See step   11 

  7. CHECK INSTRUMENT PANEL WIRE (OPEN) 
    1. Disconnect the instrument panel wire connector from the engine room main wire.
      GTY386282Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      The service wire has already been inserted into connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      DA3-2 - DA3-1 Always Below 1 Ω
    3. Disconnect the service wire from connector B.
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag ECU Assembly
      *3 Engine Room Main Wire
      *4 Instrument Panel Wire
      *5 Service Wire
      *a Front view of wire harness connector
      (to Airbag ECU Assembly)
      *b Front view of wire harness connector
      (to Engine Room Main Wire)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK → REPLACE ENGINE ROOM MAIN WIRE 

  8. CHECK INSTRUMENT PANEL WIRE (SHORT) 
    1. Disconnect the instrument panel wire connector from the engine room main wire.
      GTY392665Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      DA3-2 - DA3-1 Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag ECU Assembly
      *3 Engine Room Main Wire
      *4 Instrument Panel Wire
      *a Front view of wire harness connector
      (to Engine Room Main Wire)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK → REPLACE ENGINE ROOM MAIN WIRE 

  9. CHECK INSTRUMENT PANEL WIRE (SHORT TO B+) 
    1. Disconnect the instrument panel wire connector from the engine room main wire.
      GTY392665Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the cable to the negative (-) battery terminal.
    3. Turn the ignition switch to ON.
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      DA3-2 - Body ground Ignition switch ON Below 1 V
      DA3-1 - Body ground Ignition switch ON Below 1 V
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag ECU Assembly
      *3 Engine Room Main Wire
      *4 Instrument Panel Wire
      *a Front view of wire harness connector
      (to Engine Room Main Wire)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK → REPLACE ENGINE ROOM MAIN WIRE 

  10. CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND) 
    1. Disconnect the instrument panel wire connector from the engine room main wire.
      GTY392665Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      DA3-2 - Body ground Always 1 MΩ or higher
      DA3-1 - Body ground Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Front Airbag Sensor RH
      *2 Airbag ECU Assembly
      *3 Engine Room Main Wire
      *4 Instrument Panel Wire
      *a Front view of wire harness connector
      (to Engine Room Main Wire)

    NG → REPLACE INSTRUMENT PANEL WIRE 

    OK → REPLACE ENGINE ROOM MAIN WIRE 

  11. USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [07/2013 - 12/2013] 
  12. REPLACE AIRBAG ECU ASSEMBLY. Refer to  REMOVAL [07/2013 - 12/2013] 
  13. REPLACE FRONT AIRBAG SENSOR RH. Refer to  REMOVAL [07/2013 - ] 
scientia non olet · About LEMON Manuals