Removal (2005/12- )

BOLT, SCREW AND NUT TABLE

Fig 1: Bolt, Screw And Nut Table
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

All bolts, screws and nuts relevant to installing and removing the lower instrument panel are shown along with their alphabet code in the table above.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
1. Remove the instrument panel (see REMOVAL ).
REMOVE STEERING PAD ASSEMBLY (See REMOVAL )
REMOVE STEERING WHEEL ASSEMBLY (See REMOVAL )
REMOVE STEERING COLUMN COVER (See REMOVAL )
REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY (See REMOVAL )
REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY (See REMOVAL )
REMOVE FRONT DOOR SCUFF PLATE LH (See REMOVAL )
REMOVE FRONT DOOR SCUFF PLATE RH (See REMOVAL )
REMOVE COWL SIDE TRIM BOARD LH (See REMOVAL )
REMOVE COWL SIDE TRIM BOARD RH (See REMOVAL )
REMOVE HEATER CONTROL AND ACCESSORY ASSEMBLY (See REMOVAL )
REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY LOWER CENTER
1. Using a screwdriver, detach the 2 claws and 2 clips.
  HINT:
  
  Tape the screwdriver tip before use.
2. Disconnect the connectors, and remove the instrument cluster finish panel.
  
  Fig 2: Detaching Claws And Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER
1. Using a clip remover, remove the clip.
2. Using a screwdriver, detach the 3 claws, and remove the instrument panel finish panel.
  HINT:
  
  Tape the screwdriver tip before use.
  
  Fig 3: Removing Clip Using Clip Remover
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
1. Push the right side wall, and then push the left wall to release the stoppers.
  
  Fig 4: Pushing Right And Left Side Wall To Release Stoppers
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Pull the glove compartment door rearward to remove it.
DISCONNECT FLOOR SHIFT PARKING LOCK CABLE ASSEMBLY (for Automatic Transaxle)
REMOVE STEERING COLUMN HOLE COVER PLATE (See REMOVAL )
DISCONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY (See REMOVAL )
REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY (See REMOVAL )
REMOVE STEERING COLUMN ASSEMBLY (See REMOVAL )

Fig 5: Pulling Glove Compartment Door Rearward
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE ANTENNA CORD SUB-ASSEMBLY
REMOVE LOWER INSTRUMENT PANEL ASSEMBLY
1. Remove the 3 bolts.
  
  Fig 6: Removing Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Remove the 3 bolts.
  
  Fig 7: Removing Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Using a clip remover, remove the clip.
  
  Fig 8: Removing Clip Using Clip Remover
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Remove the 3 bolts.
  
  Fig 9: Removing Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Remove the bolt and No. 1 instrument panel mounting bracket.
  
  Fig 10: Removing Bolt And No. 1 Instrument Panel Mounting Bracket
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Remove the screw.
7. Disconnect the connector, and remove the door control receiver.
  
  Fig 11: Removing Screw
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. Remove the bolt.
9. Disconnect the hood lock control cable.
10. Remove the 2 bolts, 2 nuts and 2 screws.
11. Remove the 2 screws and 3 nuts, and disconnect the instrument panel junction block.
12. Disconnect the connectors, and then remove the instrument panel.
  
  Fig 12: Removing Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Fig 13: Removing Instrument Panel
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002