LEMON Manuals: Even more car manuals for everyone
Home >> Saturn >> 2006 >> Vue Red Line, AWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 4 (Engine Controls - 2.2L (L61) - Troubleshooting & Diagnosis) >> Inspection/Maintenance (I/M) Evaporative Emission (EVAP) System Set Procedure >> Diagnostic Aids

Diagnostic Aids

WARNING: This page is about a different variant/trim than selected.

Extreme high or low ambient temperatures may prevent the EVAP System Tests from initiating. Performing a visual inspection prior to running the test may prevent having to repeat the test. A loose fuel cap may cause a test to abort or fail and prevent the I/M System Status from updating. A failed or aborted test will require the vehicle to cool down in order to meet the enable criteria to run another test.

If there is an impending failure, the system may require more time to run the diagnostic than was allotted in the set procedure. If the test does not run after numerous attempts and no DTC is set, review the appropriate scan tool data list and the service information for an indication of why the test does not complete. Some tests may abort due to changes in the conditions while the test is running. For example, changes in engine load, such as a cooling fan or an A/C compressor clutch turning ON, may cause the test to abort.

Inspection/Maintenance (I/M) Evaporative Emission (EVAP) System Set Procedure

Step Action Yes No
1 Did you perform the Inspection/Maintenance (I/M) System Check? Go to Step 2  Go to Inspection/Maintenance (I/M) System Check 
2
  1. Ensure the vehicle is within the Conditions for Running specified in the supporting text.
  2. Turn OFF all of the accessories, e.g., air conditioning (A/C), blower fan, etc.
    3. IMPORTANT: Once the engine is started, DO NOT turn the engine OFF for the remainder of the procedure.
  3. Start the engine and idle.
    4. CAUTION: Refer to Road Test Caution in Cautions and Notices.
    IMPORTANT: In order for this test to run, the vehicle must operate in the following conditions:
  4. Accelerate at part throttle to 72 km/h (45 mph) with this speed maintained until the engine reaches operating temperature. This may be up to 10 minutes depending on the start up coolant temperature.
  5. Continue the operating conditions for an additional 3 minutes after the engine reaches operating temperature.
  6. Decelerate to 0 km/h (0 mph).
  7. Allow the engine to idle for 2 minutes or until the I/M System Status indicator updates to YES.
Did the EVAP System Status update to YES?		 Go to Step 5  Go to Step 3 
3 Observe the DTC Information with a scan tool.
Does the scan tool indicate any failed DTCs?		 Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information Go to Step 4 
4
  1. Refer to the Inspection/Maintenance (I/M) System DTC Table  to determine which DTCs are required to run in order to complete this test.
  2. Observe the Not Ran Since Code Cleared display with a scan tool.
  3. Determine which of the DTCs required for a YES status has not run.
  4. Enter the DTC number in the Specific DTC menu of the scan tool.
  5. Operate the vehicle within the Conditions for Running the DTC, located in the supporting text for the diagnostic table of the DTC.
  6. Repeat the procedure until the scan tool indicates the diagnostic test has run. This may take up to 2 hours.
  7. Repeat steps 4-6 for any additional required DTCs that have not run.
  8. Observe the I/M System Status display with a scan tool.
Did the EVAP System Status update to YES?		 Go to Step 5  Go to Diagnostic Aids
5 Observe the Emission Related DTC portion of the I/M System Status display with a scan tool.
Does the scan tool indicate any Emission Related DTCs set?		 Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information System OK
scientia non olet · About LEMON Manuals