LEMON Manuals: Even more car manuals for everyone
Home >> Saturn >> 2002 >> SC2 Automatic, MP6 >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Instrument Panel, Gages, And Console -- "S" Series >> Repair Instructions >> Instrument Cluster Replacement >> Installation Procedure

Installation Procedure

    Fig 1: Instrument Panel Cluster
    GM866637Courtesy of GENERAL MOTORS CORP.
    NOTE: Refer to Fastener Notice in Cautions and Notices.
  1. Install the instrument panel cluster.
    1. Place the tabs on the bottom of the I/P cluster into the retainer assembly.
    2. Install the screws.

      Tighten:  Tighten the I/P cluster-to-I/P housing screws to 2.2 N.m (19 lb in).

    3. Connect the electrical connector to the I/P cluster.
    2. Fig 2: I/P Bezel
    GM866615Courtesy of GENERAL MOTORS CORP.
  2. Install the I/P cluster bezel.
    1. Position the I/P cluster bezel by lining up the clip location.
    2. Snap the I/P cluster bezel in place by pushing at the clip locations.
    3. Connect the wiring harness connector for the dimmer/traction control switch.
    3. Fig 3: Upper And Lower Steering Column Shroud And Fasteners
    GM866520Courtesy of GENERAL MOTORS CORP.
  3. Position the upper steering column shroud.
    4. Fig 4: Pry The Edges Of The Ignition Lock Bezel
    GM866448Courtesy of GENERAL MOTORS CORP.
  4. Position the lower steering column shroud and install the screws.

    Tighten:  Tighten the steering column shroud fasteners to 1.5 N.m (13 lb ft).

    1. Align the peg of the ignition bezel with the cut-out in the lower shroud.
    2. Snap into place.
    5. Fig 5: Left Endcap Assembly
    GM869218Courtesy of GENERAL MOTORS CORP.
  5. Install the left endcap assembly:
    1. Maneuver the assembly past the inner I/P retainer assembly and weatherstrips.
    2. Snap the clips into the I/P retainer assembly locations.
    3. Install the screws.

      Tighten:  Tighten the I/P endcap-to-I/P screws to 2.2 N.m (19 lb in).

    6. Fig 6: Steering Column Filler Panel Bolts
    GM866671Courtesy of GENERAL MOTORS CORP.
    NOTE: Be careful not to damage the VIN plate when removing or replacing the upper trim panel.
  6. Install the steering column filler panel.

    Tighten:  Tighten the steering column filler panel fasteners to 2.2 N.m (19 lb in).

    7. Fig 7: Instrument Panel Upper Trim
    GM869041Courtesy of GENERAL MOTORS CORP.
  7. Enable the head curtain inflator modules, if equipped. Refer to DISABLING & ACTIVATING AIR BAG SYSTEM in AIR BAG RESTRAINT SYSTEMS article in RESTRAINTS.
    8. Fig 8: Instrument Panel Upper Trim
    GM866425Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: Be sure the upper trim panel seal is correctly seated on the forward edge before installing the upper trim panel.
  8. Install the upper trim panel:
    1. Ensure that the hook-and-loop fastener attachments on the upper trim panel are correctly inserted.
    2. Position the upper trim panel on the retainer assembly.
    3. Align the tabs on the sides of the upper trim panel with the openings in the windshield garnish molding.
    4. Align the clips and the clip location.
    5. Firmly snap in the clips at the clip locations.
    6. Install the screws on the underside of the upper trim panel on the passenger side of the vehicle.

      Tighten:  Tighten the I/P upper trim panel fasteners to 6 N.m (53 lb in).

  9. Enable the SIR system. Refer to DISABLING & ACTIVATING AIR BAG SYSTEM in AIR BAG RESTRAINT SYSTEMS article in RESTRAINTS.
scientia non olet · About LEMON Manuals