LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2024 >> Taycan Base >> Repair and Diagnosis >> Accessories & Equipment >> Infotainment >> 91 Radio, On-Board Computer Park Assist -- Y1A - TAYCAN (Y1A) >> WM, 912841 Repairing Antenna Cable >> Repairing Antenna Cable

Repairing Antenna Cable

  1. Determine the antenna line system of the affected antenna cable.

    Use gauge -3-  from the > VAS 6720 - antenna line repair kit  to check which antenna line system is used in the antenna cable that is to be repaired.

    G15566418Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Antenna line system gauge

    1  Antenna line system RG-174 = blue
    2  Antenna line system RTK-031 = black
  2. Fit stripping tool -1-  on crimping pliers -2-  from the > VAS 6720 - repair kit for antenna lines  in -Arrow direction-  .
    G15566419Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Stripping tool on crimping pliers

    1. 2.1  Unlock pins -3-  .
    2. 2.2 For antenna line system RTK-031: 

      Fit VAS 6720/1  stripping tool RTK-031 on crimping pliers -2-  .

    3. 2.3  For antenna line system RG 174:

      Fit VAS 6720/3  stripping tool RG-174 on crimping pliers -2-  .

    4. 2.4  Lock pins -3-  .
  3. When repairing a section:

    Remove the corresponding antenna cable for antenna line system RTK-031 or RG-174 from the > VAS 6720 - antenna line repair kit  and shorten it to the required length.

  4. Cut antenna cable -2-  .
    G15566420Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Antenna cable

    1. 4.1  Position antenna cable -2-  in the cutting tool for VAS 6720/1 or VAS 6720/3 stripping tool -1-  .
    2. 4.2  Close and then open the crimping pliers again.
    3. 4.3  Remove antenna cable -2-  .
  5. Strip antenna cable outer jacket using VAS 6720/1  or VAS 6720/3  stripping tool -1-  .
    G15566421Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Antenna cable outer jacket

    1. 5.1  Push antenna cable -2-  into mounting -3-  until stop -4-  .
    2. 5.2  Close and then open the crimping pliers again.
    3. 5.3  Pull antenna cable -2-  out of VAS 6720/1  or VAS 6720/3  stripping tool -1-  .

      Information 

      • The locating pin must move smoothly. 
      • Absolute cleanliness of the rotary cutting segment must be ensured. Any remaining shielding strands must be removed carefully before use. 
  6. Position antenna cable -1-  in rotary cutting segment -2-  of VAS 6720/1 or VAS 6720/3 stripping tool -3-  .
    G15566422Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Antenna cable in rotary cutting segment

    1. 6.1  Push locating pin -4-  in -Arrow direction-  into rotary cutter segment -2-  as far as it will go.
    2. 6.2  Push antenna cable -1-  into rotary cutting segment -2-  as far as it will go, making sure that locating pin -4-  is pushed completely out of the rotary cutting segment.
  7. Strip the shielding of the antenna cable with VAS 6720/1  or VAS 6720/3  stripping tool -1-  .
    G15566423Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Shield on antenna cable

    1. 7.1  Engage the knife holder of rotary cutter segment -2-  in -Arrow direction A-  , making sure that gap -3-  is completely closed.
    2. 7.2  Hold antenna cable -4-  securely.
    3. 7.3 -5-  Turn the rotary cutting segment -Arrow direction B-  in until it can turn easily.

      Information 

      • If the shielding strands have not been cut fully to the required length, this must be done manually. 
      • Make sure that all of the shielding strands are facing the cable connection point. 
      • Make sure that the insulation and shielding are completely removed from the rotary cutting segment. If necessary, a small screwdriver can be used to push it through the hole in the locating pin. 
  8. Remove antenna cable -1-  from the rotary cutting segment -2-  .
    G15566424Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Rotary cutting segment

    1. 8.1  Pull out release bolt -3-  in -Arrow direction A-  until the blade holder detaches from antenna cable -1-  .
    2. 8.2  Push locating pin -4-  in -Arrow direction B-  into rotary cutting segment -2-  as far as it will go, thereby pushing antenna cable -1-  out of rotary cutting segment -2-  .
    3. 8.3  Remove antenna cable -1-  .
    4. 8.4  Remove the shielding from antenna cable -1-  .
  9. Strip the internal insulation of the antenna cable with VAS 6720/1  or VAS 6720/3  stripping tool -1-  .
    G15566425Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Antenna cable internal insulation

    1. 9.1  Push antenna cable -2-  into mounting -3-  until stop -4-  .
    2. 9.2  Close and then open the crimping pliers again.
    3. 9.3  Pull antenna cable -2-  out of VAS 6720/1  or VAS 6720/3  stripping tool -1-  .
  10. Fit crimping tool -1-  on crimping pliers -2-  from the > VAS 6720 - repair kit for antenna lines  in the direction of the arrow.
    G15566426Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Crimping tool on crimping pliers

    1. 10.1  Unlock pins -3-  .
    2. 10.2 For antenna line system RTK-031: 

      Fit VAS 6720/2  crimping tool RTK-031 on crimping pliers -2-  .

    3. 10.3 For antenna line system RG-174: 

      Fit VAS 6720/4  crimping tool RG-174 on crimping pliers -2-  .

    4. 10.4  Lock pins -3-  .
  11. Insert inner contact -1-  into VAS 6720/2  or VAS 6720/4  crimping tool -2-  and secure it.
    G15566427Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Inner contact

    1. 11.1  Fold out pivot positioner -3-  .
    2. 11.2  Open positioning plate -4-  by pressing in -Arrow direction-  .
    3. 11.3  Push inner contact -1-  into pivot positioner -3-  as far as it will go.
    4. 11.4  Close positioning plate -4-  .
    5. 11.5  Fold in pivot positioner -3-  .
  12. Crimp the inner conductor of antenna cable -1-  with VAS 6720/2  or VAS 6720/4  crimping tool -2-  .
    G15566428Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Inner conductor for antenna cable

    1. 12.1  Push the inner conductor of antenna cable -1-  into inner contact -3-  .
    2. 12.2  Close the crimping pliers completely until the crimping pliers open again automatically.
    3. 12.3  Open positioning plate -4-  by pressing in -Arrow direction-  .
    4. 12.4  Remove antenna cable -5-  .
  13. Position outer contact -1-  on antenna cable -4-  .
    G15566429Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Outer contact on antenna cable

    1. 13.1  Slide sleeve -3-  over antenna cable -4-  .
    2. 13.2  Slide outer contact -1-  completely over inner conductor -2-  and slide knurled contact area -5-  over the aluminum foil and under shielding -6-  .
    3. 13.3  Position shielding -6-  on knurled contact area -5-  .
    4. 13.4  Slide sleeve -3-  over shielding -6-  .

      Information 

      Make sure that no shielding strands stick out after crimping. Any that do need to be removed.

  14. Crimp the inner conductor of antenna cable -1-  with VAS 6720/2  or VAS 6720/4  crimping tool -2-  .
    G15566430Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Outer contact on antenna cable

    1. 14.1  Fold out -3-  pivot positioner.
    2. 14.2  Insert outer contact of antenna cable -1-  in center profile -4-  of VAS 6720/2  or VAS 6720/4  crimping tool -2-  .
    3. 14.3  Close the crimping pliers completely until the crimping pliers open again automatically.
    4. 14.4  Remove antenna cable -5-from VAS 6720/2  or VAS 6720/4  crimping tool -2-  .
  15. To connect the antenna lines using antenna socket connectors, insulate the insulation and crimp each line with antenna pin connectors.
  16. Fit the connector housing for antenna socket connector -1-or the connector housing for antenna pin -2-  .
    G15566431Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Antenna pin connector housing and antenna socket connector housing

    1. 16.1  Open locking mechanism -3-  in -Arrow direction A-  .
    2. 16.2  Insert antenna cable -4-  into the relevant connector housing in -Arrow direction-  .
    3. 16.3  Lock locking mechanism -3-  in -Arrow direction B-  .
    4. 16.4  Check that antenna cable -4-  is fitted securely in the connector housing by pulling it gently.
  17. In case of damage to the antenna cable within the cable run: 

    Repair antenna cable section.

    1. 17.1  Install the socket connector and pin connector on the antenna cylinder you have just cut according to steps  1- 16.
    2. 17.2  Connect the adapter cable for the corresponding damaged antenna cable with the socket connector and pin connector according to steps  1- 16.
scientia non olet · About LEMON Manuals