LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2023 >> Taycan Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 76 (21 Exhaust Gas Turbocharging 2.9L Turbo Hybrid -- 971 - PANAMERA (971)) >> WM, 214319 Removing And Installing Charge-Air Cooler >> Installing Charge Air Cooler

Installing Charge Air Cooler

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2023 Porsche Panamera, 2022 Porsche Panamera, 2021 Porsche Panamera, 2020 Porsche Panamera, and 2019 Porsche Panamera. However, it is still accessible from the selected car via links, so may be relevant.

Information 

The procedure for removing and installing is described for one side as an example. The procedure for the other side is almost identical.

  1. Disconnect pressure hoses.
    1. 1.1 Loosen screw-type clamp -arrow-  and pull off pressure hose -1-  on the charge-air cooler -2-  .
    2. 1.2 Loosen screw-type clamp -arrow-  and pull off pressure hose -3-  on the pressure pipe -4-  .
    G15877946Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Pressure hose on pressure pipe

  2. Disconnect electric lines -1-  and connectors on the air guide -2-  for the charge-air cooler.
    1. 2.1 Open the holder -Arrows-  and loosen wiring harness -1-  .
      G15877947Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Wiring harness on air guide for charge-air cooler

  3. Loosen connector strip -1-  on the charge-air cooler.
    1. 3.1 Release connector strip -1-  (-arrow-  ) and remove it from the tab -2-  .
      G15877948Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Electric lines on air guide for charge-air cooler

  4. Remove charge-air cooler -1-  .
    1. 4.1 Unscrew screws -2-  and -3-  .
    2. 4.2 Move charge-air cooler outwards and remove it together with the pressure hose.
    G15877949Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Charge-air cooler (left)



  1. Install charge-air cooler -1-  .
    1. 1.1 Position charge-air cooler with pressure hose in installation position.
    2. 1.2 Tighten screw -2-  to > Tightening torque 9 Nm (6.5 ftlb.)  .
    3. 1.3 Tighten screws -3-  to > Tightening torque 6.5 Nm (4.75 ftlb.)  .
    G15877950Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Charge-air cooler (left)

  2. Secure connector strip -1-  on the charge-air cooler.
    1. 2.1 Fit connector strip -1-  into the tab -2-  and lock it -arrow-  .
      G15877951Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Electric lines on air guide for charge-air cooler

  3. Secure electric lines -1-  and connectors on the air guide -2-  for the charge-air cooler.
    1. 3.1 Secure wiring harness -1-  at the holders -arrows-  .
      G15877952Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Wiring harness on air guide for charge-air cooler

  4. Secure pressure hoses.
    1. 4.1 Connect pressure hoses -1-  and -3-  and tighten screw-type clamps to -Arrows-  .

      Upper screw-type clamp:  > Tightening torque 5.5 Nm (4 ftlb.) +/- 0.5 Nm (0.3 ftlb.) 

      Lower screw-type clamp:  > Tightening torque 5.5 Nm (4 ftlb.) +/- 0.5 Nm (0.3 ftlb.) 

      G15877953Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Pressure hose on pressure pipe

scientia non olet · About LEMON Manuals