LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2023 >> Taycan Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 46 (2X Petrol, Exhaust, Engine-Electric - General 2.9L Turbo Gas -- 971 - PANAMERA (971)) >> WM, 2X00IN Technical Values (V6 Turbo) >> Vacuum System (V6 BITURBO) >> Injection System

Injection System

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2023 Porsche Panamera, 2022 Porsche Panamera, 2021 Porsche Panamera, 2020 Porsche Panamera, and 2019 Porsche Panamera. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Injection System Components Location With Torque Specification - V6 Biturbo
G15877750Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Injection system V6 biturbo

1  High-pressure pump
2  High-pressure pump piston
3  Screws, M8 x 25 > Initial tightening 20 Nm (14.8 ftlb.)  > Final tightening + 45° 
4  Fuel collection pipe
5  Screw, M6 x 16 > Tightening torque 9 Nm (6.6 ftlb.) 
6  Fuel collection pipe
7  Adapter > Tightening torque 40 Nm (29.5 ftlb.) 
8  High-pressure fuel line/Coat thread on union nuts with Microgleit DF 977S. Observe drying time of at least 5 minutes before fitting./Observe the tightening sequence 
9 High-pressure fuel line connection between bank 1 and 2/Coat thread on union nuts with Microgleit DF 977S. Observe drying time of at least 5 minutes before fitting./Observe the tightening sequence 
10  Clamps
11  M6 screw
12  Fuel line flow
13  Support
14  Fuel pressure sensor for high pressure > Tightening torque 25 Nm (18.4 ftlb.) 
15  M6 nut > Tightening torque 9 Nm (6.6 ftlb.) 
16  Fuel pressure sensor for low pressure > Tightening torque 15 Nm (11.1 ftlb.) 
17  Low-pressure fuel line distributor/Coat thread on union nuts with Microgleit DF 977S. Observe drying time of at least 5 minutes before fitting./Observe specified tightening sequence  > Tightening torque 8 Nm (5.9 ftlb.)  > Tightening torque 60° 
18  Screw, M6 x 12 > Tightening torque 9 Nm (6.6 ftlb.) 
Fig 2: Shield For High-Pressure Pump Components Location With Torque Specification
G15877751Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Overview of shield for high-pressure pump

1  Shield
2  Crash support
3  Screws PT 7 x 22 > Tightening torque 14 Nm (10.3 ftlb.) 
4  Screw, M6 x 12 > Tightening torque 8 Nm (5.9 ftlb.) 
5  Screw, M6 x 25 > Tightening torque 8 Nm (5.9 ftlb.) 
Location Description Type Basic value Tolerance
Fastening screws for ground lines for left cylinder head Item 1 Tightening torque 9 Nm (6.6 ftlb.)  
G15877752Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Fastening screws for ground lines for left cylinder head
Ground line for right cylinder head Item 1 Tightening torque 9 Nm (6.6 ftlb.)  
G15877753Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Ground line for right cylinder head
G15877754Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Ground line for right cylinder head, bottom