LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2023 >> Taycan Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 145 (37 Automatic Transmission - Actuator, Housing 3.0L Turbo -- 971 - PANAMERA (971)) >> WM, 373419 Removing And Installing Double-Clutch Transmission (V6) >> Installing PORSCHE Double-Clutch Transmission

Installing PORSCHE Double-Clutch Transmission

WARNING: This page is about a different car, the 2020 Porsche Panamera, 2019 Porsche Panamera, 2018 Porsche Panamera, and 2017 Porsche Panamera. However, it is still accessible from the selected car via links, so may be relevant.
  1. Check whether input shaft is fitted with a circlip on the double-clutch shaft splines. If not:
    1. 1.1 Coat shaft splines -3-  with Longtime 3EP. 
    2. 1.2 Carefully fit input shaft -1-  until the circlip -2-  engages -Arrow-  .
      G15888056Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Input shaft

  2. Mount transmission on engine.
    1. 2.1 Deactivate parking lock.

      > 387411 ACTIVATING AND DEACTIVATING PARKING LOCK

    2. 2.2 Fit transmission and mount it on the engine by turning the output shaft.
    3. 2.3 Activate parking lock.

      > 387411 ACTIVATING AND DEACTIVATING PARKING LOCK

  3. Secure transmission on the engine.
    1. 3.1 Screw in new screws -1-  and -2-  by hand.
      G15888057Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Screws

    2. 3.2 Screw in and tighten screws -Arrows-  in transmission support > Initial tightening 25 Nm (19 ftlb.)  + > Torque angle 90° 
      G15888058Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Screws

    3. 3.3 Fit bracket -2-  and screw in new screws -1-  by hand.
      G15888059Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Holder

  4. Tighten screws.
    1. 4.1 Tighten screws -1-  to -4-  in the specified tightening sequence > Initial tightening 20 Nm (15 ftlb.)  + > Torque angle 60° 
    2. 4.2 Tighten screws -6-  to -9-  in the specified tightening sequence > Initial tightening 15 Nm (11 ftlb.)  + > Torque angle 105° 
      Fig 1: Transmission Flange Screws Tightening Sequence
      G15888060Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Tightening sequence for transmission flange

  5. For all-wheel drive vehicles: 
    1. 5.1 Replace circlip -1-  and O-ring -2-  on input flange on four wheel final drive.
      1. 5.1.1 Coat input flange -Arrow-  on all-wheel final drive lightly with Longtime 3EP. 
        G15888061Courtesy of PORSCHE CARS NORTH AMERICA, INC.

        Circlip and O-ring on all-wheel flange

    2. 5.2 Install connecting shaft -3-  .
      G15888062Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Using impact puller 9799

      1. 5.2.1 Fit connecting shaft -3-  on the all-wheel final drive and install using > 9799 - impact puller-1-Arrow-  .
    3. 5.3 Check installation position of the connecting shaft -1-  . The connecting shaft is fitted correctly if the groove -2-  is visible.
      G15888063Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Groove in connecting shaft

    4. 5.4 Remove > 9799 - impact puller  from the connecting shaft.
  6. The remaining installation steps are performed in reverse order.
scientia non olet · About LEMON Manuals