LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2023 >> Macan T >> Repair and Diagnosis >> External Pages >> Different car >> Section 3 (50 - Body Front) >> WM, 503955 Replacing Spring Strut Mount >> Removing Spring Strut Mount

Removing Spring Strut Mount

WARNING: This page is about a different car, the 2021 Porsche Macan, 2020 Porsche Macan, and 2019 Porsche Macan. However, it is still accessible from the selected car via links, so may be relevant.
  1. Remove wing bracket.
    G14360630Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Wing bracket

    1. 1.1  Drill out spot welds using > VAS 882 001 - spot-weld remover  .
    2. 1.2  Grind down welded seams -1-  .
  2. Loosen the hidden weld point.
    G14360631Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Notch

    1. 2.1  Cut out notch -LHD vehicle -  .
    2. 2.2  Drill out spot-weld using > VAS 882 001 - spot-weld remover. 
  3. Remove reinforcements.
    G14360632Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Reinforcements

    Information 

    Loosen connection points on one side only. Do not damage the sheet-metal panel underneath.

    1. 3.1  Drill out spotwelds using > VAS 882 001 - spotweld remover. 
    2. 3.2  Make a rough cut -1-  .
    3. 3.3  Mark and make cut -2-  .

      > Distance 80 mm 

    4. 3.4  Grind down welded seam -A-  .
  4. Heat marked bending surface using > V.A.G 1416 - hot-air blower  .
    G14360633Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Reinforcements

  5. Remove reinforcements.
  6. Remove remaining piece of upper reinforcement -1-  .
    G14360634Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Remaining piece

    Information 

    Loosen connection points on one side only. Do not damage the sheet-metal panel underneath.

    1. 6.1  Drill out spotwelds using > VAS 882 001 - spotweld remover  .
  7. Drill out weld points on the wiper holder or grind them using a belt sander.
    G14360635Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Wiper holder

  8. Drill out spotwelds using > VAS 882 001 - spotweld remover. 
    G14360636Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Spring strut mount

  9. Drill out spotwelds using a > VAS 882 001 - spotweld remover and grind down welded seams -Arrows-  .
    G14360637Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Spring strut mount

    G14360638Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Spring strut mount

  10. Drill out spotwelds -A-  from the inside.
    G14360639Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Spring strut mount

  11. Drill out spotwelds on the lower part of the plenum panel using a > VAS 882 001 - spotweld remover. 
    G14360640Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Lower part of plenum panel

  12. Heat marked bonding surfaces using > V.A.G 1416 - hot-air blower  .
    G14360641Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Lower part of plenum panel

  13. Remove lower part of plenum panel.
  14. Drill out spotwelds -A-  using > VAS 882 001 - spot-weld breaker. 
    G14360642Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Spring strut mount

  15. Heat marked bonding surfaces using > V.A.G 1416 - hot-air blower  .
    G14360643Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Spring strut mount

  16. Remove spring strut mount
scientia non olet · About LEMON Manuals