Replacing Rear Spoiler

Information 

Clean bonding areas.

• The bonding area must be free of dust and grease. 
• The specified drying time must be observed after cleaning. 
• Always wear protective gloves while bonding. 

1. Screw in new  rubber stop -1-  .

   Courtesy of PORSCHE CARS NORTH AMERICA, INC.

   Rubber stop on rear spoiler

2. Stick new  sealing lip on rear spoiler.
   1. 2.1 Clean the bonding area -1-  using suitable cleaning agents.

      Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Bonding area on sealing lip

   2. 2.2 Pull protective film off adhesive strip.
   3. 2.3 Press sealing lip -1-  onto the rear spoiler by hand.
   4. 2.4 Stick on sealing lip -1-  using > 9886/1 - press-on roller  . > Contact force 50 N  /cm²

   Courtesy of PORSCHE CARS NORTH AMERICA, INC.

   Sealing lip on rear spoiler

3. Stick adhesive strip -2-  onto new  spoiler lip -1-  .

   Courtesy of PORSCHE CARS NORTH AMERICA, INC.

   Adhesive strip on spoiler lip

   1. 3.1 Clean bonding area of spoiler lip -1-  .
   2. 3.2 Pull off protective film on adhesive strip -2-  .
   3. 3.3 Stick adhesive strip -2-  onto the spoiler lip -1-  .
4. 15-mm spoiler lip: Install new  spoiler lip -1-  .
   1. 4.1 Measure positioning tape -2-  for aligning the spoiler lip -1-  and cut it to size.

      Centre positioning tape: > Length 139.5 mm 

      Outer positioning tape: > Length 153.5 mm 

   2. 4.2 Stick positioning tape -2-  onto the rear spoiler -3-  . When doing so, the positioning tape -2-  must be aligned flush with the edge -4-  and centred with respect to the recesses -5-  .
   3. 4.3 Clean the rear spoiler -3-  in the spoiler lip area -1-  .
   4. 4.4 Clip in spoiler lip -1-  and make sure that the clips engage securely.
   5. 4.5 Align spoiler lip -1-  with the positioning tape -2-  .

      Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Positioning tape for 15-mm spoiler lip

   6. 4.6 Visually align the spoiler lip with the design edges -1-  of the rear spoiler.

      Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Aligning 15-mm spoiler lip

   7. 4.7 Pull off protective film on adhesive strip -2-  and press spoiler lip -1-  onto the rear spoiler with your hand.
   8. 4.8 Stick spoiler lip -1-  onto the rear spoiler using > 9886/1 - press-on roller  . > Contact force 50 N  /cm²

      Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      15-mm spoiler lip

5. 25-mm spoiler lip: Install new  spoiler lip -1-  .
   1. 5.1 Measure positioning tape -2-  for aligning the spoiler lip -1-  and cut it to size.

      Centre positioning tape: > Length 115 mm 

      Outer positioning tape: > Length 132.2 mm 

   2. 5.2 Stick positioning tape -2-  onto the rear spoiler -3-  . When doing so, the positioning tape -2-  must be aligned flush with the edge -4-  and centred with respect to the recesses -5-  .
   3. 5.3 Clean the rear spoiler -3-  in the spoiler lip area -1-  .
   4. 5.4 Clip in spoiler lip -1-  and make sure that the clips engage securely.
   5. 5.5 Align spoiler lip -1-  with the positioning tape -2-  .

      Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Positioning tape for 25-mm spoiler lip

   6. 5.6 Visually align the spoiler lip with the edges -1-  of the rear spoiler.

      Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Aligning 25-mm spoiler lip

   7. 5.7 Pull off protective film on adhesive strip -2-  and press it onto the rear spoiler with your hand.
   8. 5.8 Stick spoiler lip -1-  onto the rear spoiler using > 9886/1 - press-on roller  . > Contact force 50 N  /cm²

      Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      25-mm spoiler lip