LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2021 >> Panamera Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 8 (10 Engine - Crankcase, Suspension 3.0L Turbo -- 971 - PANAMERA (971)) >> WM, 100119 Removing And Installing Engine >> Subsequent Work

Subsequent Work

WARNING: This page is about a different car, the 2020 Porsche Panamera, 2019 Porsche Panamera, 2018 Porsche Panamera, and 2017 Porsche Panamera. However, it is still accessible from the selected car via links, so may be relevant.
  1. Secure pressure hoses at the bottom on both sides of the charge-air cooler.

    > Tightening torque 5.5 Nm (4 ftlb.) +/- 0.5 Nm (0.3 ftlb.) 

  2. V8 Turbo only:  Install air guide -1-  at the radiator frame.
    1. 2.1 Position air guide -2-  and secure with clips.
      G15821254Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Air guide at top of radiator frame

  3. Install air-cleaner cowl -1-  .

    > 242719 REMOVING AND INSTALLING AIR-CLEANER COWL

    1. 3.1 Tighten screw-type clamps -3-  .

      Screw-type clamp securing cowl to air cleaner housing: > Tightening torque 5 Nm (3.5 ftlb.) 

      G15821255Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Air-cleaner cowl

  4. Secure intake scoops -1-  .
    1. 4.1 Connect intake scoops and tighten screw-type clamps -2-  .

      Screw-type clamp on air box for intake pipe: > Tightening torque 3.5 Nm (2.5 ftlb.) 

      G15821256Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Intake scoop

  5. Install engine cover.

    > WM, 108319 REMOVING AND INSTALLING ENGINE COVER (DESIGN COVER) (V6 TURBO) 

  6. Install engine compartment trim panel.

    > WM, 700219 REMOVING AND REINSTALLING FRONT TRIM PANEL (ENGINE COMPARTMENT)

  7. Install front wheel housing liners.

    > Removing and installing front wheel housing liner 

  8. Install rear cardan shaft.

    > 393519 REMOVING AND INSTALLING REAR CARDAN SHAFT

  9. Secure ATF lines to the ATF cooler.

    > WM, 386219 REMOVING AND INSTALLING ATF COOLING LINE (REAR SECTION) , WM, 386219 REMOVING AND INSTALLING ATF COOLING LINE (FRONT SECTION)

  10. Secure air-conditioning lines to the cooler.

    > 875019 REMOVING AND INSTALLING CONDENSER

  11. Install exhaust system.

    > WM, 260119 REMOVING AND INSTALLING EXHAUST SYSTEM

  12. Fill up coolant.

    > WM, 193817 DRAINING AND FILLING COOLANT

  13. Fill in refrigerant.

    > 870317 DRAINING AND FILLING REFRIGERANT R1234YF

  14. Check engine oil.

    > WM, 170101 CHECKING ENGINE-OIL LEVEL

  15. Connect battery ground strap.

    > WM, 270619 REMOVING AND REINSTALLING BATTERY

    > Tightening torque 6 Nm (4.5 ftlb.) 

  16. Fill in ATF.

    > WM, 370235 CHECKING AND TOPPING UP ATF

  17. Perform suspension alignment.

    > 449503 PERFORMING FRONT AND REAR SUSPENSION ALIGNMENT

  18. Perform a test drive.

    After the cooling system has cooled down again, check the engine coolant level in the reservoir and top up to the Maximum mark if necessary.

scientia non olet · About LEMON Manuals