Turbocharger (Monoturbo)

WARNING: This page is about a different car, the 2020 Porsche Panamera, 2019 Porsche Panamera, 2018 Porsche Panamera, and 2017 Porsche Panamera. However, it is still accessible from the selected car via links, so may be relevant.

Fig 1: Turbocharger Components Location With Torque Specification (Monoturbo)

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Turbocharger (monoturbo)

1	Turbocharger
2	Shut-off valve
	O-ring replace
3	Screws (M6 x 18) > Tightening torque 9 Nm (6.6 ftlb.)
4	Nuts (M8) stud/replace > Tightening torque 25 Nm (18.4 ftlb.)
5	Stud > Tightening torque 15 Nm (11.1 ftlb.)
6	Nuts (M8) dowel studs/replace > Tightening torque 30 Nm (22.1 ftlb.)
7	Clamp
8	Dowel stud > Tightening torque 15 Nm (11.1 ftlb.)
9	Decoupling element
10	V-band clip/replace > Tightening torque 20 Nm (14.8 ftlb.)
11	Gasket/replace
12	Speed sensor
13	Screw (M4 x 14)/ > Tightening torque 5 Nm (3.7 ftlb.)
14	Nozzle
15	Sealing ring (A16 x 20)/replace (A16 x 20)
16	Screw plug (M16 x 1 x 7.5) > Tightening torque 25 Nm (18.4 ftlb.)
17	Active carbon filter line
18	O-ring (7.65 x 1.76)/replace
19	Vacuum modulator
19.1	> Setpoint value 8 mm +/- 1 mm
19.2	> Setpoint value 3 mm +/- 1 mm
20	Nuts (M6) > Tightening torque 8 Nm (5.9 ftlb.)
21	Bolts
22	Safety clip

ohne Abb. Shut-off valve

ohne Abb. Screws (M6 x 18) > Tightening torque 9 Nm (6.6 ftlb.)

ohne Abb. Screw (M6 x 14) > Tightening torque 9 Nm (6.6 ftlb.)

Fig 2: Lock Nuts On Control Box Components Location With Torque Specification

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Lock nuts on control box

1 + 3

Lock nut on control rod > Tightening torque 8 Nm (5.9 ftlb.)

Coolant lines and oil lines on turbocharger

Fig 3: Coolant Lines And Oil Lines On Turbocharger Components Location With Torque Specification - V6 Monoturbo

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Coolant lines and oil lines on turbocharger - V6 monoturbo

1	Turbocharger
2	Coolant return line
3	O-ring/replace
4	Screw (M6 x 12) > Tightening torque 9 Nm (6.6 ftlb.)
5	Screw (M6 x 16) > Tightening torque 9 Nm (6.6 ftlb.)
6	Oil feed line
7	O-ring/replace
8	O-ring/replace
9	Coolant supply line
10	O-ring/replace
11	Bracket
12	Oil return pipe/must always be replaced after removal
13	Pin/must always be replaced after removal

Fig 4: Coolant Line On Left Cylinder Bank Components Location With Torque Specification

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Coolant line on left cylinder bank

1	Coolant return line for turbocharger to left cylinder head
2	Screw > Tightening torque 9 Nm (6.6 ftlb.)