Technical Values
WARNING: This page is about a different variant/trim than selected.
| Location | Description | Type | Basic value | Tolerance 1 | Tolerance 2 |
|---|---|---|---|---|---|
| Oil plate to crankcase | Screw, M6 x 20 | Tightening torque | 13 Nm (9.5 ftlb.) | ||
| Screw plug | M30 x 1.5 | Tightening torque | 80 Nm (59 ftlb.) | ||
| Main bearing screw for crankcase: Step 1 | M10 x 195 (12.9) with sealing washer | Initial tightening | 5 Nm (3.5 ftlb.) | ||
| Main bearing screw for crankcase: Step 2 | M10 x 195 (12.9) with sealing washer | Initial tightening | 15 Nm (11 ftlb.) | ||
| Main bearing screw for crankcase: Step 3 | M10 x 195 (12.9) with sealing washer - wait 3 minutes after tightening | Initial tightening | 50 Nm (37 ftlb.) | ||
| Main bearing screw for crankcase: Step 4 | Loosen all screws | Loosening | 0 Nm (0 ftlb.) | ||
| Main bearing screw for crankcase: Step 5 | M10 x 195 (12.9) with sealing washer | Initial tightening | 5 Nm (3.5 ftlb.) | ||
| Main bearing screw for crankcase: Step 6 | M10 x 195 (12.9) with sealing washer | Tightening torque | 15 Nm (11 ftlb.) | ||
| Main bearing screw for crankcase: Step 7 | M10 x 195 (12.9) with sealing washer - set threshold torque of 15 Nm (11 ftlb.) | Torque angle | 75° | ||
| Main bearing screw for crankcase: Step 8 | M10 x 195 (12.9) with sealing washer | Torque angle | 75° | ||
| Cross bolt connection on crankcase | M6 x 40 | Tightening torque | 13 Nm (9.5 ftlb.) | ||
| Additional cross bolt connection | M8 x 35 | Tightening torque | 33 Nm (24 ftlb.) | ||
| Bearing pin for guide and tensioning rails | M6 | Tightening torque | 10 Nm (7.5 ftlb.) | ||
| Connecting rod bolt: Step 1 | M10 x 1.25 x 51 | Initial tightening | 5 Nm (3.5 ftlb.) | ||
| Connecting rod bolt: Step 2 | M10 x 1.25 x 51 | Subsequent tightening torque | 16 Nm (12 ftlb.) | ||
| Connecting rod bolt: Step 3 | M10 x 1.25 x 51 | Tightening torque | 20 Nm (15 ftlb.) | ||
| Connecting rod bolt: Step 4 | M10 x 1.25 x 51 | Torque angle | + 80° | ||
| Connecting rod bolt: Step 5 | M10 x 1.25 x 51 | Loosen screws | - 360° | ||
| Connecting rod bolt: Step 6 | M10 x 1.25 x 51 | Initial tightening | 5 Nm (3.5 ftlb.) | ||
| Connecting rod bolt: Step 7 | M10 x 1.25 x 51 | Subsequent tightening torque | 16 Nm (12 ftlb.) | ||
| Connecting rod bolt: Step 8 | M10 x 1.25 x 51 | Tightening torque | 20 Nm (15 ftlb.) | ||
| Connecting rod bolt: Step 9 | M10 x 1.25 x 51 | Torque angle | + 80 | ° +/- 3° |