Installing logo rear

Information 

Not for PORSCHE logo.

The logo is replaced together with the trim.

Information 

• Carefully clean any dirt, grease, wax and other impurities off the fitting area of the body using isopropanol. 
• Always use a clean cloth. 
• The room and object temperature must be at least > Nominal value + 15°C  .
• Humidity should be > Nominal value 50 % +/- 10 %  .
• Do not touch the bonding surface again after removing the protective paper. 
• Wear clean gloves during the bonding process in order to guarantee adequate adhesion. 
• The parts must have been bonded for at least > Nominal value 72 h  before washing the vehicle in a car wash.

Logo template 718 Boxster_ECE > 9904 - Logo template 718 Boxster_ECE 

Logo template 718 Boxster_US > 9904/1 - Logo template 718 Boxster_US 

Logo template 718 Boxster S_ECE > 9904/2 - Logo template 718 Boxster S_ECE 

Logo template 718 Boxster S_US > 9904/3 - Logo template 718 Boxster S_US 

Logo template 718 Boxster GTS_ECE > 9948 - Logo template "718 Boxster GTS" (ECE) 

Logo template 718 Boxster GTS_US > 9948/1 - Logo template "718 Boxster GTS" (US) 

Logo template 718 Boxster T_ECE > 9948/4 - Logo template "718 Boxster T" (ECE) 

Logo template 718 Boxster T_US > 9948/5 - Logo template "718 Boxster T" (US) 

Logo template 718 Cayman_ECE > 9904/4 - Logo template 718 Cayman_ECE 

Logo template 718 Cayman_US > 9904/5 - Logo template 718 Cayman_US 

Logo template 718 Cayman S_ECE > 9904/6 - Logo template 718 Cayman S_ECE 

Logo template 718 Cayman S_US > 9904/7 - Logo template 718 Cayman S_US 

Logo template 718 Cayman GTS_ECE > 9948/2 - Logo template "718 Cayman GTS" (ECE) 

Logo template 718 Cayman GTS_US > 9948/3 - Logo template "718 Cayman GTS" (US) 

Logo template 718 Cayman T_ECE > 9948/6 - Logo template "718 Cayman T" (ECE) 

Logo template 718 Cayman T_US > 9948/7 - Logo template "718 Cayman T" (US) 

Logo template 718 ECE > 9904/8 - Logo template 718 ECE 

Logo template 718 US > 9904/9 - Logo template 718 US 

Logo template 718 GT4_ECE > 9928/2 - Logo template "GT4" (ECE) 

Logo template 718 GT4_US > 9928/3 - Logo template "GT4" (US) 

Logo template 718 Spyder_ECE > 9928 - Logo template "718 Spyder" (ECE) 

Logo template 718 Spyder_US > 9928/1 - Logo template "718 Spyder" (US) 

Logo template 718 Boxster 25_ECE > 9948/8 - Logo template "Boxster 25" (ECE) 

Logo template 718 Boxster 25_US > 9948/9 - Logo template "Boxster 25" (US) 

1. Position logo template on the vehicle.
   1. 1.1 Insert logo template into the gap between the rear bumper and the spoiler output drive.

   Courtesy of PORSCHE CARS NORTH AMERICA, INC.

2. Remove the protective paper from the logo.
3. Align the logo -1-  using the logo template -2-  and press it on firmly.

   Courtesy of PORSCHE CARS NORTH AMERICA, INC.

4. Removing the logo template from the vehicle.