Removing Wire Harness For Engine (R4)
- Disconnect Section of line at the left.
Section of line at the left
- 1.1 Release and disconnect electric plug connection on oil level sensor -1- .
- 1.2 Release and disconnect electric plug connection on water pump -2- .
- 1.3 Release and disconnect electric plug connection for oil pressure control valve -3- .
- 1.4 Loosen fixing clips -4- .
- Unclip fixing clip -1-
and guide Section of line -2-
to the rear under the coolant pipes -Arrow-
.
Coolant pipes
- Disconnect Section of line for oil pressure switch.
Electric plug connection
- 3.1 Release and disconnect electric plug connection on oil pressure switch -1- .
- 3.2 Release and disconnect electric plug connection for pulse sender -2- .
- 3.3 Release and disconnect cable holder -3- .
- Disconnect Section of line at the left.
Section of line at the left
- 4.1 Release and disconnect electric plug connection on throttle valve -1- .
- 4.2 Release and disconnect electric plug connection for fuel injectors -2- .
- 4.3 Release and disconnect electric plug connection for fuel pressure sensor -3- .
- 4.4 Loosen fixing clips -4- .
- 4.5 Release and disconnect electric plug connection for knock sensor -5- .
- 4.6 Release and disconnect electric plug connection on vacuum valve -6- .
- Release and disconnect electric plug connections for Section of line at the right.
Section of line at the right
- 5.1 Release and disconnect electric plug connection on oil pressure switch -1- .
- 5.2 Release and disconnect electric plug connection for oil pressure control valve -2- .
- 5.3 Release and disconnect electric plug connection on oil pressure switch -3- .
- 5.4 Release and disconnect electric plug connection on vacuum valve -4- .
- 5.5 Unclip fixing clips for Section of line at the top right -5- .
- Release and disconnect electric plug connection on pressure sensor -1-
.
Pressure sensor
- Disconnect Section of line for camshaft control valve.
Section of line at the top
- 7.1 Release and disconnect electric plug connection for intake camshaft control valve -1- .
- 7.2 Release and disconnect electric plug connection for exhaust camshaft control valve -2- .
- 7.3 Release and disconnect electric plug connection for boost pressure adjuster -3- .
- 7.4 Unclip fixing clip -4- .
- Disconnect Section of line for fuel pressure control valve.
Fuel pressure control valve
- 8.1 Release and disconnect electric plug connection for fuel pressure control valve -1- .
- 8.2 Unclip fixing clip -2- .
- Disconnect Section of line for oxygen sensor -2-
.
Section of line for oxygen sensor
- 9.1 Unclip electric plug connection for oxygen sensor -1- from cable duct bracket -3- and release and disconnect it.
- 9.2 Unclip section of line for oxygen sensor -2- from cable duct bracket -4- .
- Disconnect Section of line for recirculating air valve for turbocharger.
Section of line for recirculating air valve for turbocharger
- 10.1 Release and disconnect electric plug connection for recirculating air valve for turbocharger -1- .
- 10.2 Release and disconnect electric plug connection for coolant temperature sensor -2- .
- 10.3 Unclip omega clip -3- for Section of line for recirculating air valve for turbocharger.
- Expose the cable duct.
Ignition coils
- 11.1 Release and disconnect electric plug connection for ignition coils -1- .
- 11.2 Release and disconnect electric plug connection on camshaft pulse sender -2- .
- 11.3 Release and disconnect electric plug connection for camshaft actuator -3- .
- Unscrew fastening nuts for ground lines -1-
and disconnect ground lines -2-
from cylinder head.
Ground straps
- Pull cable duct -1-
off bracket -2-
and bracket -3-
and set it aside.
Cable duct
- Guide wire harness for engine (R4) to the left side and set it down.
- Disconnect wire harness for engine (R4) from engine control unit.
Engine control module
- 15.1 Release and disconnect electric plug connection for main wire harness -1- .
- 15.2 Release and disconnect electric plug connections for engine control unit -2- .
- 15.3 Unclip fixing clip -3- for Section of line for engine control unit.
- Remove wire harness for engine (R4) from the vehicle.