Loosening Main Wire Harness In Luggage Compartment At The Right
NOTIFICATION
Incorrect handling of main wire harness
- Risk of damage to lines
- → The main wire harness contains all airbag lines, antenna lines and optical waveguides.
- → The main wire harness must not be separated and is always replaced as a complete wire harness when carrying out extensive repairs.
- → If individual lines are damaged, shut off these lines and install new lines. Lay the new lines along the main wire harness and secure them to the main wire harness.
- Press rubber sleeve -1-
into the passenger compartment and glide section of line for right tail light -2-
into the passenger compartment.
Section of line for right tail light
- Release and disconnect electric plug connection for RPM sensor -1-
> 451519 REMOVING AND INSTALLING REAR SPEED SENSOR
Electric plug connection for RPM sensor
- Release and disconnect electric plug connection for brake pad wear indicator -2-
.
Electric plug connection for brake pad wear indicator
- Pull line bracket -3-
for section of line for the chassis at the right -4-
out of the retaining bracket.
Line bracket for section of line for chassis, right
- Release and disconnect electric plug connection on parking brake spreader device -1-
.
> 468519 REMOVING AND INSTALLING SPREADER DEVICE
Electric plug connection on parking brake spreader device
- Release and disconnect electric plug connection for airbag sensor on rear right wheel bearing housing -2-
.
> 695119 REMOVING AND INSTALLING AIRBAG SENSOR
Airbag sensor on rear right wheel bearing housing
- Pull line bracket -3-
for section of line for the chassis at the right -4-
out of the retaining bracket.
Section of line for chassis, right
- Unclip line bracket -1-
for section of line for chassis at the right -2-
.
Line bracket for section of line for chassis, right
- Disconnect ground lines -1-
from fuel filler neck.
Ground lines on fuel filler neck
- Release and disconnect electric plug connection for rear right damping adjustment -2-
.
Electric plug connection for rear right damping adjustment
- Unclip line bracket -4-
for section of line for chassis at the right -5-
.
Line bracket
- Press rubber sleeve -3-
into the passenger compartment and guide section of line for the chassis at the right -5-
into the passenger compartment.
Rubber sleeve
- Release and disconnect electric plug connection for tank vent valve
> 202319 REMOVING AND INSTALLING TANK VENT VALVE (V6 MONOTURBO)
Electric plug connection for tank vent valve
- Press rubber sleeve -2-
into the passenger compartment and guide section of line for the tank vent valve -3-
into the passenger compartment.
Section of line for tank vent valve
- Release and disconnect electric plug connections for auxiliary heating control unit
> 821819 REMOVING AND INSTALLING AUXILIARY HEATING CONTROL UNIT
Electric plug connections for auxiliary heating control unit
- Release and disconnect electric plug connections for mobile phone antenna amplifier -2-
.
> 914519 REMOVING AND INSTALLING MOBILE PHONE ANTENNA AMPLIFIER
Electric plug connections for mobile phone antenna amplifier
- Release and disconnect electric plug connections on control unit for rear spoiler -3-
.
> Refer to the appropriate service information.
Electric plug connections on control unit for rear spoiler
Information
Handling optical waveguides:
- Optical waveguides must not be kinked.
- Optical waveguides must not be crushed.
The ends of the optical waveguide must be checked for dirt and soiling before installation.
- Unclip, release and disconnect electric plug connections at connection point for rear apron -1-
.
Electric plug connections at connection point for rear apron
- Press rubber sleeve -1-
into the tailgate.
Rubber sleeve in tailgate
- Pull rubber sleeve -1-
out of the tailgate and guide section of line for rear spoiler out of the tailgate.
Rubber sleeve in tailgate
- Press rubber sleeve -1-
into the passenger compartment and guide section of line for the rear spoiler -2-
into the passenger compartment.
Rubber sleeve for section of line for rear spoiler
- Unclip section of line for rear spoiler -1-
from the holders -2-
.
Section of line for rear spoiler
- Open holder -3-
and unclip electric plug connection at connection point for roof at the left -4-
from the holder.
Electric plug connection at connection point for roof, left
Information
Handling optical waveguides:
- Optical waveguides must not be kinked.
- Optical waveguides must not be crushed.
The ends of the optical waveguide must be checked for dirt and soiling before installation.
- Release and disconnect electric plug connection
Electric plug connection
- Release and disconnect electric pug connection at connection point for the roof -2-
.
Electric plug connection at connection point for roof
- Unscrew fastening screw -3-
at ground point for the roof at the left and remove ground lines.
Fastening screw for ground point for roof, left
- Release and disconnect electric plug connection for head airbag at the right -1-
> 696619 REMOVING AND INSTALLING HEAD AIRBAG
Electric plug connection for head airbag, right
- Unclip line bracket -2-
on section of line for head airbag at the right -3-
.
Line bracket for section of line for head airbag, right
- Remove water drain hose for panoramic roof -1-
from line brackets for main wire harness for luggage compartment at the right -2-
.
Water drain hose for panoramic roof
- Unclip line bracket -1-
for section of line for the roof -2-
.
Line bracket for section of line for roof
- Unclip line bracket -1-
for main wire harness for luggage compartment at the right -2-
.
Main wire harness in luggage compartment, right
- Release and disconnect electric plug connections for loudspeaker booster -3-
.
> 914419 REMOVING AND INSTALLING LOUDSPEAKER BOOSTER
Electric plug connections for loudspeaker booster
- Remove holder for loudspeaker booster.
Holder for loudspeaker booster
- 33.1 Remove fastening screws
- 33.2 Remove fastening nuts -2- .
- 33.3 Remove holder for loudspeaker booster together with loudspeaker booster -3- .
- Release and disconnect electric plug connection for antenna amplifier (on side window) at the right
> 918419 REMOVING AND INSTALLING ANTENNA AMPLIFIER (SIDE WINDOW)
Electric plug connection for antenna amplifier (on side window), right
- Unclip line bracket -2-
and lay section of line for tank cap release in the passenger compartment.
Section of line for tank cap release
- Unclip line bracket -3-
for main wire harness for luggage compartment at the right.
Main wire harness in luggage compartment, right
- Release and disconnect electric plug connection for rear three-point belt -1-
> 691219 REMOVING AND INSTALLING REAR THREE-POINT BELT
Electric plug connection for rear three-point belt
- Release and disconnect electric plug connection for right seat heating resistor -2-
.
Electric plug connection for seat heating resistor, right
- Release and disconnect electric plug connection for airbag sensor on inner right C-pillar -3-
.
> 695119 REMOVING AND INSTALLING AIRBAG SENSOR
Electric plug connection for airbag sensor on inner right C-pillar
- Unscrew fastening nut -1-
from ground point for rear right wheel housing and remove ground lines.
Ground point for rear right wheel housing
- Unscrew fastening nut -2-
from rear right ground point and remove ground lines.
Rear right ground point
- Unclip line bracket -3-
for main wire harness for luggage compartment at the right.
Line bracket for main wire harness for luggage compartment at the right