WM 2X00IN Technical Values (MACAN): Overview: Notes
NOTE:
- The tightening steps in the tightening sequences relate to tightening screws uniformly, i.e. all affected screws must first be tightened uniformly to the first torque value, then all screws are tightened one stage further, and so on.
- Replace all O-rings following removal!
The torques specified in the table below generally apply to screws that are not specifically listed =>
The bolt quality is indicated on the screw head at the top as a decimal number, e.g. "8.8" or "12.9".
| Bolt quality 8.8 | Bolt quality 10.9 | Bolt quality 12.9 | |||
|---|---|---|---|---|---|
| Thread | [Nm (ftlb.)] | Thread | [Nm (ftlb.)] | Thread | [Nm (ftlb.)] |
| M4 | → Tightening torque: 3 Nm (2 ftlb.) | M4 | → Tightening torque: 4 Nm (3 ftlb.) | M4 | → Tightening torque: 5 Nm (3.5 ftlb.) |
| M5 | → Tightening torque: 6 Nm (4.5 ftlb.) | M5 | → Tightening torque: 8 Nm (6 ftlb.) | M5 | → Tightening torque: 10 Nm (7.5 ftlb.) |
| M6 | → Tightening torque: 10 Nm (7.5 ftlb.) | M6 | → Tightening torque: 13 Nm (9.5 ftlb.) | M6 | → Tightening torque: 16 Nm (12 ftlb.) |
| M8 | → Tightening torque: 23 Nm (17 ftlb.) | M8 | → Tightening torque: 33 Nm (24 ftlb.) | M8 | → Tightening torque: 39 Nm (29 ftlb.) |
| M10 | → Tightening torque: 45 Nm (33 ftlb.) | M10 | → Tightening torque: 65 Nm (48 ftlb.) | M10 | → Tightening torque: 80 Nm (59 ftlb.) |
| M10 x 1.25 | → Tightening torque: 50 Nm (37 ftlb.) | M10 x 1.25 | → Tightening torque: 70 Nm (52 ftlb.) | M10 x 1.25 | → Tightening torque: 85 Nm (63 ftlb.) |
| M12 | → Tightening torque: 80 Nm (59 ftlb.) | M12 | → Tightening torque: 115 Nm (85 ftlb.) | M12 | → Tightening torque: 135 Nm (100 ftlb.) |
| M12 x 1.25 | → Tightening torque: 90 Nm (67 ftlb.) | M12 x 1.25 | → Tightening torque: 125 Nm (93 ftlb.) | M12 x 1.25 | → Tightening torque: 150 Nm (111 ftlb.) |
| M12 x 1.5 | → Tightening torque: 85 Nm (63 ftlb.) | M12 x 1.5 | → Tightening torque: 120 Nm (89 ftlb.) | M12 x 1.5 | → Tightening torque: 145 Nm (107 ftlb.) |
| M14 | → Tightening torque: 130 Nm (96 ftlb.) | M14 | → Tightening torque: 180 Nm (133 ftlb.) | M14 | → Tightening torque: 220 Nm (163 ftlb.) |
| M16 | → Tightening torque: 200 Nm (148 ftlb.) | M16 | → Tightening torque: 280 Nm (207 ftlb.) | M16 | → Tightening torque: 335 Nm (248 ftlb.) |