Convertible Top, Hardtop
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2019 Porsche 911, 2018 Porsche 911, 2017 Porsche 911, 2016 Porsche 911, and 2015 Porsche 911. However, it is still accessible from the selected car via links, so may be relevant.
| Location | Description | Type | Basic value | Tolerance 1 | Tolerance 2 |
|---|---|---|---|---|---|
| Fastening nuts on convertible-top compartment lid | Tightening torque | 9.7 Nm (7.5 ftlb.) | |||
|
Removing convertible-top compartment lid |
|||||
| Fastening nut for convertible-top compartment lid | Targa | Tightening torque | 9.7 Nm (7.5 ftlb.) | ||
|
Removing convertible-top compartment lid |
|||||
| Fastening screw securing strut to convertible-top compartment lid bracket | Item 3 | Tightening torque | 9.7 Nm (7.5 ftlb.) | ||
|
Positioning glass dome |
|||||
| Fastening screws on trim panel for rear lid | Tightening torque | 2.2 Nm (1.5 ftlb.) | +/-0.2 Nm (+/- 0.1 ftlb.) | ||
|
Installation position of trim panel |
|||||
| Fastening nut securing rear window to convertible-top compartment lid | Tightening torque | 9.7 Nm (7.5 ftlb.) | |||
|
Removing rear window |
|||||
| Fastening screw for air deflector | Tightening torque | 3.4 Nm (2 ftlb) | |||
|
Removing air deflector |
|||||
| Fastening screws for upper part of lid lock | Tightening torque | 9.7 Nm (7.5 ftlb.) | |||
|
Removing upper part of lid lock |
|||||
| Fastening screws for front convertible top mount | Tightening torque | 36 Nm (27 ftlb.) | |||
|
Removing convertible top mount |
|||||
| Fastening screw for hydraulic cylinder | Tightening torque | 9.7 Nm (7.5 ftlb.) | |||
|
Pulling off safety clips |
|||||
| Fastening screw on convertible top support | Tightening torque | 23 Nm (17 ftlb.) | |||
|
Loosening convertible top support |
|||||
| Fastening screws for front lock | Tightening torque | 9.7 Nm (7.5 ftlb.) | |||
|
Removing lock |
|||||
| Fastening screw securing potentiometer to convertible top | Tightening torque | 2.7 Nm (2 ftlb.) | |||
|
Removing position sensor |
|||||
| Fastening nut for convertible-top compartment lid hinge | Tightening torque | 23 Nm (17 ftlb.) | |||
| Fastening screw for convertible-top compartment lid hinge | Tightening torque | 23 Nm (17 ftlb.) | |||
|
Loosening hinge |
|||||
| Fastening screw for convertible-top compartment lid hinge | Item 2 | Tightening torque | 23 Nm (17 ftlb.) | ||
|
Removing hinge |
|||||
| Fastening nut for convertible-top compartment lid hinge | Item 1 | Tightening torque | 23 Nm (17 ftlb.) | ||
|
Removing hinge |
|||||
| Gap dimension from side panel to convertible-top compartment lid (A) | Perfectly aligned | Gap dimension | 3.9 mm | +1 mm | -0.7 mm |
| Gap dimension from side panel/spoiler to convertible-top compartment lid (B) | Perfectly aligned | Gap dimension | 4.5 mm | +/-0.8 mm | |
|
Gap dimensions |
|||||