Technical Values

WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2013 Porsche 911, 2012 Porsche 911, 2011 Porsche 911, 2010 Porsche 911, and 2009 Porsche 911. However, it is still accessible from the selected car via links, so may be relevant.

Location	Description	Type	Basic value
Pin securing tensioning and guide rails on crankcase		Length	74.5 mm
Pin for guide and tensioning rails	M16	Tightening torque	31 Nm (23 ft. lb.)
Chain box to crankcase	M8	Tightening torque	23 Nm (17 ft. lb.)
Threaded bolt for top guide rail	M16	Tightening torque	31 Nm (23 ft. lb.)
Camshaft housing	M8 x 50	Initial tightening	23 Nm (17 ft. lb.)
Camshaft housing	M8 x	50 Final tightening	28 Nm (21 ft. lb.)
Spark plug	New part	Tightening torque	30 Nm (22 ft. lb.)
Ignition coil	M6 Torx socket screw	Tightening torque	10 Nm (7.5 ft. lb.)
Covers for intake camshafts	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Oil suction pump/tandem pump	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Oil/tandem pump to cylinder head	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Heat exchanger bracket to crankcase	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Oil-filter housing	Grease O-ring	Tightening torque	25 Nm (19 ft. lb.)
Large oil/water heat exchanger	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Small oil/water heat exchanger	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Secondary unit carrier to crankcase	M10 x 60	Tightening torque	65 Nm (48 ft. lb.)
Coolant pipe to crankcase	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Holder for heating tubes with B+ line	M6 x 55	Tightening torque	10 Nm (7.5 ft. lb.)
Pulse sender holder	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Oil supply line for turbocharger	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Wire harness	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Union nut on clutch pressure line	M12	Tightening torque	30 Nm (22 ft. lb.)
Holder for run-on pump	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Holder for oil-filter console	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Oil line for suction pump on engine, side 4-6	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Oil extraction line to crankcase	M16 banjo bolt	Tightening torque	30 Nm (22 ft. lb.)
Oil line for suction pump on engine, side 1-3	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Clamp securing oil return line to engine oil tank	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Oil return line to oil suction pumps	M22 x 1.5; counter at the same time	Tightening torque	40 Nm (30 ft. lb.)
Heat shield for ignition coils	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Lines for turbocharger oil tank	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Three-hole flange to turbocharger	Lock nut, M8	Tightening torque	28 Nm (21 ft. lb.)
Turbocharger holder	M8	Tightening torque	23 Nm (17 ft. lb.)
Turbocharger to holder	M8	Tightening torque	23 Nm (17 ft. lb.)
Exhaust temperature sensor	Union nut, a/f 14	Tightening torque	35 Nm (26 ft. lb.)
Clamps for oil supply lines	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Coolant connection piece to cylinder housing	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Oil return line flange to oil/water heat exchanger	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Union nut securing oil return line to crankcase		Tightening torque	30 Nm (22 ft. lb.)
Engine strut to crankcase	M10	Tightening torque	65 Nm (48 ft. lb.)
Combination valve for secondary air	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Fuel return line to pressure regulator		Tightening torque	30 Nm (22 ft. lb.)
Throttle body holder	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Ground cable to cover of camshaft housing	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Secondary air pump to intake distributor 1-3	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Intake air line to turbocharger	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Oil tank	M8	Tightening torque	23 Nm (17 ft. lb.)
Intake air line to turbocharger	M6	Tightening torque	10 Nm (7.5 ft. lb.)
Return line to oil tank	M30 x 1.5; counter at the same time	Tightening torque	60 Nm (44 ft. lb.)
Rear silencer to turbocharger	Replace lock nuts	Tightening torque	25 Nm (19 ft. lb.)
Clamps for rear silencer	M8 hexagon socket	Tightening torque	23 Nm (17 ft. lb.)