Technical values: Overview
WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2013 Porsche 911, 2012 Porsche 911, 2011 Porsche 911, 2010 Porsche 911, and 2009 Porsche 911. However, it is still accessible from the selected car via links, so may be relevant.
| Location | Description | Type | Basic value | Tolerance 1 | Tolerance 2 |
|---|---|---|---|---|---|
| Threaded connection securing brake pressure line to brake master cylinder, M12 x 1 | Tightening torque was increased to 25 Nm/19 ftlb. (also applies to older vehicles). Counter using special tool 9763 while tightening | Tightening torque | 25 Nm (19 ftlb.) | ||
| Threaded connection securing brake pressure line to hydraulic unit, M12 x 1 | Tightening torque was increased to 25 Nm/19 ftlb. (also applies to older vehicles) | Tightening torque | 25 Nm (19 ftlb.) | ||
| Threaded connection securing brake pressure line to hydraulic unit, M10 x 1 | Tightening torque | 16 Nm (12 ftlb.) | |||
| Threaded connection securing brake pressure line to distributor, brake hose and brake calliper, M10 x 1 | Tightening torque | 16 Nm (12 ftlb.) | |||
| Threaded connection securing brake pressure line to intermediate piece, M10 x 1 | Centre underbody | Tightening torque | 16 Nm (12 ftlb.) | ||
| Threaded connection securing brake pressure line to intermediate piece, M12 x 1 | Centre underbody | Tightening torque | 25 Nm (19 ftlb.) | ||
| Threaded connection securing brake booster to body, M8 | Tightening torque | 23 Nm (17 ftlb.) | |||
| Threaded connection securing brake unit support to body, M8 | Tightening torque | 23 Nm (17 ftlb.) | |||
| Threaded connection securing brake master cylinder to brake booster, M14 | Tightening torque | 49 Nm (36 ftlb.) | |||
| Threaded connection securing brake pressure line to brake master cylinder, M12 x 1 | Tightening torque was increased to 25 Nm/19 ftlb. (also applies to older vehicles). Counter using special tool 9763 while tightening | Tightening torque | 25 Nm (19 ftlb.) | ||
| Threaded connection securing bracket for hydraulic unit to body, M6 | Tightening torque | 4 Nm (3 ftlb.) | |||
| Threaded connection securing hydraulic unit to bracket, M6 | Tightening torque | 5.5 Nm (4 ftlb.) | |||
| Threaded connection securing brake pressure line to hydraulic unit, M10 x 1 | Tightening torque | 16 Nm (12 ftlb.) | |||
| Threaded connection securing brake pressure line to hydraulic unit, M12 x 1 | Tightening torque | 25 Nm (19 ftlb.) | |||
| Threaded connection securing brake calliper to wheel carrier, M12 x 1.5 | Replace screws on front and rear axle whenever removed. | Tightening torque | 85 Nm (63 ftlb.) | ||
| Threaded connection securing brake pressure line to brake calliper, M10 x 1 | Tightening torque | 16 Nm (12 ftlb.) | |||
| Threaded connection securing connecting line to brake calliper, M10 x 1 | Tightening torque | 12 Nm (9 ftlb.) | |||
| Threaded connection securing bleeder screw to brake calliper, M10 x 1 | Tightening torque | 8-12 Nm (6 - 9 ftlb.) |