Technical Values

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2016 Porsche Panamera, 2015 Porsche Panamera, 2014 Porsche Panamera, 2013 Porsche Panamera, and 2012 Porsche Panamera. However, it is still accessible from the selected car via links, so may be relevant.

Location	Description	Type	Basic value	Tolerance 1	Tolerance 2
Trailer hitch to body		Tightening torque	50 Nm (37 ftlb.)
Screw-in sequence for trailer hitch fastening screws
Trailer hitch to body		Torque angle	180°
Screw-in sequence for trailer hitch fastening screws
Rear apron fastening screws		Tightening torque	2.8 Nm (2.1 ftlb.)	+/-0.5 Nm (+/-0.5 ftlb.)
Screws on frame for light
Lateral retaining strip		Tightening torque	4.8 Nm (3.5 ftlb.)	+/-1 Nm (+/-0.5 ftlb.)
Removing lateral retaining strip
Centre retaining strip to end plate		Tightening torque	4.8 Nm (3.5 ftlb.)	+/-1 Nm (+/-0.5 ftlb.)
Centre retaining strip
Lower retaining strip to end plate		Tightening torque	4.8 Nm (3.5 ftlb.)	+/-1 Nm (+/-0.5 ftlb.)
Removing lower holder
Fastening screw for holder with heat protection		Tightening torque	4.8 Nm (3.5 ftlb.)	+/-1 Nm (+/-0.5 ftlb.)
Removing holder with heat protection
Fastening nut for holder with heat protection		Tightening torque	4.8 Nm (3.5 ftlb.)	+/-1 Nm (+/-0.5 ftlb.)
Removing holder with heat protection
Fastening screw securing bumper to bodyshell		Tightening torque	65 Nm (48 ftlb.)	+/-6.5 Nm (+/-5 ftlb.)
Removing bumper
Fastening screw, retaining strip		Tightening torque	2.8 Nm (2 ftlb.)
Installing front holder
Front apron to lock carrier		Tightening torque	5 Nm	+/-0.5 Nm (+/-0.5 ftlb.)
Front screws at the top
Front apron to lateral wing		Tightening torque	2.8 Nm (2 ftlb.)	+/-0.5 Nm (+/-0.5 ftlb.)
Wing screw
Fastening screw securing bumper to longitudinal member		Tightening torque	50 Nm (37 ftlb.)	+5 Nm (+3.5 ftlb.)	-7.5 Nm (-5.5 ftlb.)
Bumper mounting
B-pillar cover to door sub-frame		Tightening torque	3.5 Nm	+10°
Securing B-pillar cover
Fastening screw for rear-view mirror	Item 1	Tightening torque	23 Nm (17 ftlb.)
Removing rear-view mirror
Fastening screw for front grab handle	Item 3	Tightening torque	5.5 Nm (4 ftlb.)
Securing front grab handle
Fastening screw for rear grab handle	Item 3	Tightening torque	5.5 Nm (4 ftlb.)
Securing front grab handle
Fastening screw for headliner	Item 1	Tightening torque	5.5 Nm (4 ftlb.)
Securing headliner
Fastening screw for sun visor	Item 1	Tightening torque	5.5 Nm (4 ftlb.)
Securing sun visor
Fastening screw for sun visor	Item 1	Tightening torque	5.5 Nm (4 ftlb.)
Installing holder
Fastening screws for sliding roof at front	Observe tightening sequence	Tightening torque	9.7 Nm
Securing sliding roof at the front
Fastening screws for sliding roof at the sides	Observe tightening sequence	Tightening torque	9.7 Nm
Securing sliding roof at the sides
Overlength seal		Length	2 mm	+1 mm
Rear cut		Length	approx. 1 mm
Trimming the seal
Fastening screw securing sliding roof panel to sliding roof trim surround	Item 2A	Tightening torque	4.5 Nm	+/-0.5 Nm (+/-0.5 ftlb.)
Adjusting height at the front
Fastening screw securing sliding roof panel to sliding roof trim surround	Item 2B, 2C	Tightening torque	4.5 Nm	+/-0.5 Nm (+/-0.5 ftlb.)
Adjusting height at the rear
Fastening screw securing lower part of center console cover		Tightening torque	2.5 Nm	+/-0.5 Nm (+/-0.5 ftlb.)
Securing cover
Fastening screw at top of center console		Tightening torque	3.2 Nm (2 ftlb.)	+/-0.5 Nm (+/-0.5 ftlb.)
Securing center console at the top
Centre console fastening screws in package box		Tightening torque	3.2 Nm (2 ftlb.)	+/-0.5 Nm (+/-0.5 ftlb.)
Securing center console
Fastening screw for front ashtray		Tightening torque	2.5 Nm	+/-0.5 Nm (+/-0.5 ftlb.)
Securing front ashtray
Front fastening screw securing center console to center tunnel	Torx screw	Tightening torque	3.2 Nm (2 ftlb.)	+/-0.5 Nm (+/-0.5 ftlb.)
Front screws
Rear fastening screw securing center console to center tunnel	Torx screw	Tightening torque	3.2 Nm (2 ftlb.)	+/-0.5 Nm (+/-0.5 ftlb.)
Installing center console
Fastening screws for cover extension in storage compartment		Tightening torque	2.5 Nm	+/-0.5 Nm (+/-0.5 ftlb.)
Securing extension for cover in storage compartment
Lower fastening screw for cover extension in storage compartment		Tightening torque	2.5 Nm	+/-0.5 Nm (+/-0.5 ftlb.)
Securing extension for cover in storage compartment
Fastening screws, rear		Tightening torque	27 Nm
Installing rear center console (Business)
Fastening screw, front and bottom		Tightening torque	3.2 Nm (2 ftlb.)	+/-0.5 Nm (+/-0.5 ftlb.)
Screwing in fastening screws at the front, bottom and sides
Fastening screws securing damper to package box cover		Tightening torque	3.2 Nm (2 ftlb.)	+/-0.5 Nm (+/-0.5 ftlb.)
Securing damper
Fastening screws securing bracket to center console		Tightening torque	2.5 Nm	+/-0.5 Nm (+/-0.5 ftlb.)
Rear cupholder (Business) to center console		Tightening torque	1.5 Nm (1 ftlb.)	+0.2 Nm (+0.1 ftlb.)	-0.4 Nm (-0.2 ftlb.)
Screwing in fastening screws
Fastening screws for glove compartment, inner/outer		Tightening torque	3.2 Nm (2 ftlb.)
Securing glove compartment at the top (inner)
Inner fastening screws for glove compartment		Tightening torque	3.2 Nm (2 ftlb.)
Securing glove compartment on the inside
Fastening screws for glove compartment, top		Tightening torque	3.2 Nm (2 ftlb.)
Securing glove compartment at the top
Fastening screws for glove compartment, lateral		Tightening torque	3.2 Nm (2 ftlb.)
Securing glove compartment at the sides
Fastening screws for knee airbag strut		Tightening torque	8 Nm	+/-0.8 Nm (+/-0.5 ftlb.)
Securing strut for knee airbag
Fastening screws for ventilation duct		Tightening torque	3.2 Nm
Securing ventilation duct
Fastening nuts for spoiler drive	Item 7	Tightening torque	9 Nm
Securing spoiler drive
Fastening screws for spoiler drive	Item 6	Tightening torque	9 Nm
Securing spoiler drive
Fastening screw securing lower part of rear spoiler to spoiler drive		Tightening torque	4.5 Nm (3 ftlb.)	+/-0.5 Nm (+/-0.5 ftlb.)
Loosening lower part of rear spoiler
Fastening screw securing closing element of rear spoiler to spoiler drive	Item (B)	Tightening torque	4.5 Nm (3 ftlb.)	+/-0.5 Nm (+/-0.5 ftlb.)
Installing closing element of rear spoiler
Fastening screw securing spoiler drive (wing) to spoiler drive	Item 1	Tightening torque	4.5 Nm (3 ftlb.)	+/-0.5 Nm (+/-0.5 ftlb.)
Installing spoiler drive (flap)
Fastening screw securing lower part of rear spoiler to spoiler drive		Tightening torque	4.5 Nm (3 ftlb.)	+/-0.5 Nm (+/-0.5 ftlb.)
Installing lower part of rear spoiler
Gap from bolt to bolt (inner side)	Dimension A	Adjustment value	556 mm
Laying spoiler drive onto special tool
Fastening nut securing spoiler drive to engine housing		Tightening torque	1 Nm (0.5 ftlb.)
Screwing off spoiler drive nuts
Fastening screw securing closing element of rear spoiler to spoiler drive		Tightening torque	4.5 Nm (3 ftlb.)	+/-0.5 Nm (+/-0.5 ftlb.)
Installing closing element of rear spoiler
Fastening screw for securing rear spoiler microswitch to spoiler drive		Tightening torque	1 Nm (0.5 ftlb.)
Installing wire harness for rear spoiler
Fastening screw securing cover on lower part of rear spoiler to spoiler drive		Tightening torque	4.5 Nm (3 ftlb.)	+/-0.5 Nm (+/-0.5 ftlb.)
Securing cover on lower part of rear spoiler
Distance from reversing lever to limit stop		Distance	20 mm
Moving motor for spoiler drive into adjustment position
Fastening screw for side window	Item 2	Tightening torque	3.5 Nm	+10°
Securing side window
Actuating bar for sun blind on door window		Torque angle	45°
Removing actuating bar for sun blind on door window
Fastening screws securing passenger's airbag unit to dashboard	4	Tightening torque	8 Nm (6 ftlb.)
Fastening screws securing passenger's airbag unit to retaining frame	5	Tightening torque	8 Nm (6 ftlb.)
Fastening screws securing bracket for trim to dashboard	2	Tightening torque	3.2 Nm (2 ftlb.)
Fastening screws securing support to dashboard	2	Tightening torque	8 Nm (6 ftlb.)
Fastening nuts for triggering unit	-1-	Tightening torque	9 Nm (6.5 ftlb.)	+10 %	-15 %
Fastening screw securing rear side airbag to catch bar	-1-	Tightening torque	10 Nm (7.5 ftlb.)	+/-1 Nm (+/-0.5 ftlb.)
Upper threaded joint securing driver's knee airbag to trim panel	Torx screw -1-	Tightening torque	3.2 Nm (2.5 ftlb.)
Driver's knee airbag to trim panel	Torx screw -1-	Tightening torque	1.4 Nm (1 ftlb.)
Screws securing knee airbag on passenger's side to glove compartment	-1-	Tightening torque	1.4 Nm (1 ftlb.)
Upper screws securing knee airbag on passenger's side to glove compartment	-1-	Tightening torque	3.2 Nm (2 ftlb.)
Fastening screw for head airbag	-1-	Tightening torque	2.7 Nm (2 ftlb.)
Fastening nut for head airbag	-2, 3-	Tightening torque	9.7 Nm (7.5 ftlb.)
Fastening screw for head airbag	-4, 5, 6, 7-	Tightening torque	2.7 Nm (2 ftlb.)
Fastening screw for head airbag	-8, 9, 10, 11-	Tightening torque	2.7 Nm (2 ftlb.)
Fastening nut securing airbag sensor to lock carrier		Tightening torque	9 Nm (6.5 ftlb.)	+1 Nm (+0.5 ftlb.)	-1.5 Nm (-1 ftlb.)
Fastening nut securing airbag sensor to inner side member		Tightening torque	9 Nm (6.5 ftlb.)	+1 Nm (+0.5 ftlb.)	-1.5 Nm (-1 ftlb.)
Fastening nut securing airbag sensor to rear wheel arch		Tightening torque	9 Nm (6.5 ftlb.)	+1 Nm (+0.5 ftlb.)	-1.5 Nm (-1 ftlb.)
Front side airbag to seat frame		Tightening torque	7 Nm (5 ftlb.)