Component Overview
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2016 Porsche Panamera, 2015 Porsche Panamera, 2014 Porsche Panamera, 2013 Porsche Panamera, and 2012 Porsche Panamera. However, it is still accessible from the selected car via links, so may be relevant.
Piston, connecting rod
| 1 | Piston-ring set; oil with engine oil; TOP marking facing upwards; oil scraper ring down; ring gaps offset by 120° |
| 2 | Piston; different on naturally aspirated and turbo engines; combustion chamber recess facing centre of engine; left and right different; arrow in direction of travel |
| 3 | Piston-pin circlip (positioned at 6 o'clock or 11 o'clock) |
| 4 | Piston pin; oil |
| 5 | Connecting rod |
| 6 | Connecting rod bolt; replace as it must be tightened in the plastic area; oil screw |
| 7 | Connecting rod bearing shells; oil with engine oil |
Connecting-rod assembly, bearing shells
| A | View A (identification area for connecting-rod number; fit connecting rod with identification area facing exhaust side; marking on rod and lid must be on the same side) |
| B | View B (fit bearing shells flush and press in by hand) |
| C | View C (fit bearing shells flush and press in by hand) |
Piston classification, naturally aspirated engine
| 1 | Marking for dimension group (just one permitted per engine, in this case x) |
| 2 | Porsche short numeric code without main or middle number |
| 3 | Short numeric code (supplier) |
| 4 | Marking area for weight group (just one permitted per engine, + or -) |
| 5 | Cylinder bank identification (V6 1-3 and 4-6) (V8 1-4 and 5-8) |
| 6 | Barcode 128 (short numeric code without main group or weight group) |
| 7 | Arrow marking in direction of travel |
| 8 | Identification for dimension group |
| 9 | Arrow marking in direction of travel |
| 10 | Inspection stamp (supplier) |
Piston classification, turbo engine
| 1 | Arrow marking in direction of travel |
| 2 | Porsche short numeric code without main or middle number |
| 3 | Short numeric code (supplier) |
| 4 | Cylinder bank identification (V8 1-4 and 5-8) |
| 5 | Marking area for weight group (just one permitted per engine, + or -) |
| 6 | Barcode 128 (short numeric code without main group or weight group) |
| 7 | Arrow marking in direction of travel |
| 8 | Marking for dimension group (just one permitted per engine, in this case x) |
| 9 | Marking area for weight group (just one permitted per engine, + or -) |
| 10 | Inspection stamp (supplier) |
Crankshaft
| 1 | Crankshaft |
| 2 | Straight pin, 6x20 |
| 3 | Spring, 5 x 6.5 |
| 4 | Thrust washer (grooves facing out) |
| 5 | Main bearing shell, upper |
| 6 | Main bearing shell, lower |
| 7 | Shaft sealing ring => Do not touch sealing ring lip! Clean crankshaft flange and oil lightly |
| 8 | View of crankshaft flange |
| 9 | Allocation of main bearing |
| 10 | Allocation of connecting-rod bearing |
| A | Direction of travel (main bearing 1 is the first in direction of travel against output) |
| B | Bearing shell with blue colour marking |
| G | Bearing shell with yellow colour marking |
| N | Bearing shell with green colour marking |
| R | Bearing shell with red colour marking |