LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2017 >> Panamera Turbo >> Repair and Diagnosis >> External Pages >> Different car >> Section 7 (70 Linings, Insulation - Wagon -- 971 - PANAMERA (971)) >> WM, 701819 Removing And Installing Dashboard >> Removing Dashboard

Removing Dashboard

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2023 Porsche Panamera, 2022 Porsche Panamera, 2021 Porsche Panamera, 2020 Porsche Panamera, and 2019 Porsche Panamera. However, it is still accessible from the selected car via links, so may be relevant.
WARNING: Improper handling of airbag units 
  • Triggering of airbag unit. 
  • System faults can occur. 

    → Switch off ignition and move remote control (hand-held transmitter) at least 2 metres away from the vehicle.

    → A voltage supply (e.g. battery charger) must not be connected to the external power supply/jump-lead starting terminals.

    → Disconnect the battery and insulate the ground strap so that all contact with a ground carrier is avoided.

    → Wait 1 minute after disconnecting the battery.

    → Only pull off connector on the triggering unit after the waiting time has elapsed.

    → Make sure that no foreign objects are located in front of the airbag unit during installation.

    → Replace damaged parts during removal.

    → Always position airbag units so that the blow-out opening is facing upwards, e.g. crest on driver's airbag.

    → Do not place any objects on the airbag units.

    → If removed for an extended period, the airbag units must be stored in a safe place.

    → Airbag units must not come into contact with grease, oil, detergents, liquids or similar substances.

    → Do not expose airbag units to temperatures above 90°.

    → Do not remove the short-circuit spring on the plug contacts.

    → Triggering and preparations may only be carried out by skilled staff, supervised by a second responsible person.

    → Before disposal, the airbag unit must be rendered harmless by triggering it electrically while observing all precautionary measures, thereby preventing it from being used incorrectly.

WARNING: Incorrect handling of safety bolts 
  • Danger of injury 
  • Loss of torque 

    → Always use new screws or nuts following removal.

    → Comply with instructions for repairs.

    → Observe specified tightening torques.

    → Carry out a visual inspection of parts used.

  1. Only for vehicles with stopwatch: 

    Unclip line bracket -3-  for electric line for stopwatch -4-  under the centre loudspeaker cover.

    G15874281Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Line bracket

  2. Unclip line bracket -1-  securing electric line for sun sensor -2-  .
    G15874282Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Electric line

  3. Unclip line bracket -5-  from electric wire harness on the passenger's side.
    G15874283Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Line bracket on passenger's side

  4. Turn air quality sensors/temperature sensors -6-  at the left and right with lines connected by 90° and remove them from the air ducts on the outer air vents.
    G15874284Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Sensors

  5. Release and disconnect electric plug connection -1-  on air ioniser -2-  .
    G15874285Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Air ioniser

  6. Unscrew screws -7-  on the driver's side.
    G15874286Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Screws on driver's side

  7. Unscrew screws -8-  on the passenger's side.
    G15874287Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Screws on passenger's side

  8. Unscrew screws -9-  .
    G15874288Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Centre screws

    Information 

    The help of another person is required.

  9. Remove dashboard on the passenger's side and guide out electric lines.
scientia non olet · About LEMON Manuals