Installing Motor

Information 

For tightening torques, tightening sequence and assembly overviews for the engine and transmission:

• Group 1: 

  > WM, 1X00IN TECHNICAL VALUES (V8 BITURBO)

• Group 2: 

  > WM, 2X00IN TECHNICAL VALUES (V8 BITURBO)

• Group 3: 

  > 3X00IN TECHNICAL VALUES

Information 

The pictures shown in this document may differ from the original.

Information 

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Adhesive tape markings on the workshop floor

• Before moving the unit elevating platform, mark the position of the wheels on the workshop floor with adhesive tape. This makes it easier to position the platform again for re-installation. 

1. Guide the engine in under the vehicle.
   1. 1.1 Move the engine under the vehicle using > VAS 6832 - Master Gear unit elevating platform  .
   2. 1.2 Position the unit elevating platform at the positions marked during removal.
   3. 1.3 Guide the engine up into the engine compartment using the lifting equipment.
2. Secure front-axle carrier.

   > 400619 Removing and installing front-axle carrier - information on  "INSTALLING "

   • Front-axle carrier to body -4-  : > Initial tightening 70 Nm (51.6 ftlb.) Final tightening + 180° 
   • V6 only:  - Front-axle carrier to body, rear -5-  : > Tightening torque 50 Nm (36.9 ftlb.) 
   • Anti-roll bar to body -6-  : > Initial tightening 70 Nm (51.6 ftlb.) Final tightening + 180° 

   Courtesy of PORSCHE CARS NORTH AMERICA, INC.

   Front-axle carrier

3. Tighten screws for transmission support.

   > Initial tightening 25 Nm (19 ftlb.) 

   > Torque angle 90° 

4. Secure the strut -1-  .
   1. 4.1 Tighten screws.

      Strut and front-axle carrier -2-  : > Initial tightening 70 Nm (51.6 ftlb.) Final tightening + 180° 

      Strut to body -3-  : > Initial tightening 50 Nm (36.9 ftlb.) Final tightening + 45° 

      Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Strut mounting

5. Remove wheel hub holder -1-  at both sides on the wheel hub.

   Courtesy of PORSCHE CARS NORTH AMERICA, INC.

   Wheel hub holder (similar to illustration)

6. Secure the spring strut to the lower trailing arm -1-  .
   1. 6.1 Tighten screws -2-  .

      > Initial tightening 90 Nm (67 ftlb.) Final tightening + 120° 

      Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Mounting for spring strut on lower trailing arm

7. Secure wheel bearing housing to the upper trailing arm -1-  .

   Hexagon nut, M12 -2-  : > Tightening torque 85 Nm (63 ftlb.) 

   Courtesy of PORSCHE CARS NORTH AMERICA, INC.

   Mounting for upper trailing arm on wheel bearing housing

8. Secure the front brake calliper to the wheel carrier.

   > 473919 REMOVING AND INSTALLING FRONT BRAKE CALLIPER

   1. 8.1 Tighten screws.

      > Initial tightening 30 Nm (22.1 ftlb.) Final tightening torque angle + 90° 

      Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Front brake calliper

9. Secure wire harness for wheel carrier.
   • Speed sensor to wheel bearing housing -1-  : > Tightening torque 8 Nm (6 ftlb.) 
   • Cable holder to wheel bearing housing -2-  : > Tightening torque 8 Nm (6 ftlb.) 
   • Brake line holder to wheel bearing housing -4-  : > Tightening torque 8 Nm (6 ftlb.) 

   Courtesy of PORSCHE CARS NORTH AMERICA, INC.

   Wire harness for wheel carrier at the front

   > 489055 REPLACING POWER-STEERING GEAR

10. Secure universal joint on the steering gear.
    1. 10.1 Position universal joint and tighten new screw.

       > Initial tightening 20 Nm (15 ftlb.) 

       > Final tightening torque angle + 90° 

11. Only for vehicles with particle filter:  Connect cable plug -1-  for exhaust temperature sensor at the left and right and check that it is fitted securely.

    Shown on one side as an example.

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Cable plug for exhaust temperature sensor

12. Secure coolant lines for heater -1 and 2-  .

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Coolant lines for heating

13. Connect electric connector -1-  to the front-axle carrier -2-  at the front right.

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Electric connector on front-axle carrier at the front right

14. Connect vacuum line for brake booster -1-  .

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Brake booster vacuum line

15. Only for vehicles with particle filter:  Secure differential pressure sensors -2-  on struts at the side.
    1. 15.1 Position differential pressure sensors and secure with screws -1-  .

       > Tightening torque 8 Nm (6 ftlb.) 

       Courtesy of PORSCHE CARS NORTH AMERICA, INC.

       Differential pressure sensors with holder

16. Secure electric lines to the diagonal brace at the right.

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Electric lines on diagonal brace at the right

17. Connect tank vent line -1-  to tank vent line -2-  .

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Tank vent line

18. Secure ground cable -1-  to the right spring strut dome.

    > Tightening torque 20 Nm (15 ftlb.) 

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Ground point for right spring strut dome

19. Connect fuel supply line -1-  .

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Fuel supply line

20. Connect coolant vent line -1-  .

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Coolant vent line

21. Secure B+ line -1-  to the relay carrier -2-  .

    > WM, 9X00IN TECHNICAL VALUES

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    B+ line on relay carrier

22. Secure torque support to the engine.

    > 103719 REMOVING AND INSTALLING TORQUE SUPPORT 

    1. 22.1 Tighten screws.

       > Initial tightening 50 Nm (36.9 ftlb.) 

       > torque angle + 90° 

23. Connect electric connectors on the pressure sensor at the left and right to the throttle valve.
24. Secure electric line for horn.

    > WM, 905019 REMOVING AND INSTALLING HORN

    Information 

    • Replace O-rings on the cooling system. 
    • Clean plug connection and coolant hoses before assembly. 
    • Remove stoppers before fitting the coolant lines and hoses. 
25. Secure coolant line -1-  to the top of the radiator -2-  .
    1. 25.1 Fit circlip -3-  .

       Courtesy of PORSCHE CARS NORTH AMERICA, INC.

       Coolant line at top of radiator

26. V8 biturbo: 

    Secure coolant line -1-  to the coolant pump -2-  .

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Coolant line on coolant pump

27. Connect vacuum line -1-  to the valve cover.

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Vacuum line for valve cover at the left

28. Connect air-conditioning line (high-pressure) -1-  in the engine compartment.

    > Tightening torque 12 Nm (9 ftlb.) 

    1. 28.1 Check O-rings and replace them if damaged.
    2. 28.2 Coat O-rings with refrigerant oil before fitting them.

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Air-conditioning line in engine compartment

29. Connect air-conditioning line (low-pressure) -1-  in the engine compartment.

    > Tightening torque 12 Nm (9 ftlb.) 

    1. 29.1 Check O-rings and replace them if damaged.
    2. 29.2 Coat O-rings with refrigerant oil before fitting them.

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Low-pressure air-conditioning line

30. Secure engine wire harness -1-  in the front left wheel housing.

    > WM, 970909 LOOSENING AND SECURING MAIN WIRE HARNESS IN ENGINE COMPARTMENT

    1. 30.1 Replace damaged holders/tie-wraps -arrows-  .

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Engine wire harness - part 2

31. Secure engine wire harness -1-  in the front left wheel housing.

    > WM, 970909 LOOSENING AND SECURING MAIN WIRE HARNESS IN ENGINE COMPARTMENT

    1. 31.1 Replace damaged holders/tie-wraps -arrows-  .

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Engine wire harness - part 1

32. Secure wire harness for steering gear -1-  .

    Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Wire harness for steering gear

33. Only for PDCC: 

    Secure wire harness to the PDCC anti-roll bar control unit.

    > 407719 REMOVING AND INSTALLING FRONT ANTI-ROLL BAR (PDCC)

34. Connect electric lines -1, 2, 3 and 5-  in front left wheel housing/underbody.
    1. 34.1 Secure ground line -5-  with a hexagon nut -4-  .

       > Tightening torque 9 Nm (6.5 ftlb.) 

       Courtesy of PORSCHE CARS NORTH AMERICA, INC.

       Electric lines in front left wheel housing