LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2017 >> Panamera Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 33 (Collision*** 5X Body - General - Coupe -- 971 - PANAMERA (971)) >> 5X00 Body - General >> WM, 5X00IN34 Thread Repairs For Threaded Bushes Without Collar >> Repair Procedure For Threaded Bush Without Collar >> Overview Of Thread Repair Kits

Overview Of Thread Repair Kits

WARNING: This page is about a different car, the 2023 Porsche Panamera and 2022 Porsche Panamera. However, it is still accessible from the selected car via links, so may be relevant.
M14 -- Installation depth variable > VAS 271 011 - Thread repair kit, M14 x 1.5 
M12 -- Installation depth 5 mm > 9843 - Thread repair kit 
M10 -- Installation depth 5 mm > 9843/1 - Thread repair kit 
M10 -- Installation depth 10 mm > 9843/2 - Thread repairs 
M8 -- Installation depth 10 mm > 9843/3 - Thread repair kit 
  1. Loosen wire threaded insert (Helicoil) -1-  using a suitable screwdriver.
    G15863430Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Loosening wire threaded insert (Helicoil)

  2. Pull out wire threaded insert (Helicoil) -1-  (-Arrows-  ).
    G15863431Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Removing wire threaded insert (Helicoil)

  3. Drill out thread.
    1. 3.1 Drill out the old thread fully using special 3-flute drill bit (contained in the set) -RHD vehicle -  .

    Minimal drilling depth = depth + length of threaded bush + approx. 3 mm 

    G15863432Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Drilling out thread

  4. Cut thread.
    G15863433Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Cutting thread

    1. 4.1 Cut thread up to dimension -Y-  using a cutting tool.

      Dimension -Y- = depth + length of threaded bush 

    2. 4.2 Clean the thread.
      1. 4.2.1 Blow drilling chips out of the thread using compressed air.
      2. 4.2.2 Rinse the thread with brake cleaner.
      3. 4.2.3 Blow-dry the thread with compressed air.
  5. Position threaded bush on screw-in tool.
    1. 5.1 Screw threaded bush -1-  onto screw-in tool -2-  .
    G15863434Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Positioning threaded bush on screw-in tool

    Check that the threaded bush -1-  is screwed fully onto the screw-in tool -2-  (-Arrows-  ).

    G15863435Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Positioning threaded bush on screw-in tool

  6. Only for screw-in tool with variable depth: Set depth. 
    G15863436Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Adjusting the depth

    1. 6.1 Loosen screw -1-  .
    2. 6.2 Adjust the stop -2-  to the relevant depth -X -  .
    3. 6.3 Tighten screw -1-  .
  7. Screw in threaded bush.
    1. 7.1 Screw in threaded bush -1-  fully immediately using the screw-in tool -2-  .
    G15863437Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Screwing in threaded bush

  8. Unscrew screw-in tool -E-  from the threaded bush -LHD vehicle -  .
    G15863438Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Unscrewing screw-in tool

    Information 

    Do not move the vehicle until after the prescribed curing time specified for the threaded bush.

    Information 

    Once the end position is reached, the threaded bush must be loaded immediately in the screw direction and the thread lock must harden in this state.

    Two options are available for this:

    • Screw on component immediately.
    • By tightening the setting tool finger-tight. Do not unscrew the setting tool until the curing time has elapsed.
  9. Leave thread lock to harden for 6 hours. Assembly work may be carried out.
scientia non olet · About LEMON Manuals