Technical values: Overview

WARNING: This page is about a different car, the 2016 Porsche Macan and 2015 Porsche Macan. However, it is still accessible from the selected car via links, so may be relevant.

TORQUE SPECIFICATION

Location	Description	Type	Basic value
ATF drain plug on oil pan		Tightening torque	45 Nm (33 ft. lb.)
Fastening screw securing ATF oil pan to transmission	M6 x 20	Tightening torque	10 Nm (7.5 ft. lb.)
Fastening screw securing control mechanism for transmission	M6 x 45	Initial tightening	8 Nm (6 ft. lb.)
Fastening screw securing control mechanism for transmission	M6 x 45	Final tightening	+90°
Fastening screw securing retaining bracket to transmission		Tightening torque	10 Nm (7.5 ft. lb.)
Fastening screw securing ATF filter housing to transmission		Tightening torque	10 Nm (7.5 ft. lb.)
Fastening screw securing ATF lines to ATF filter housing		Tightening torque	20 Nm (15 ft. lb.)
ATF inspection plug		Tightening torque	60 Nm (44 ft. lb.)
Fastening screw for ATF connector housing		Tightening torque	8 Nm (6 ft. lb.)
Fastening screw securing cable guide for RPM sensors to transmission		Tightening torque	8 Nm (6 ft. lb.)
Fastening screws	ATF oil pan	Tightening torque	10 Nm (7.5 ft. lb.)
Fastening screws	Heat shield to front-axle carrier	Tightening torque	9 Nm (6.5 ft. lb.)
Fastening screw	Heat shield to front-axle carrier	Tightening torque	20 Nm (15 ft. lb.)
Fastening screws	Heat shield over engine mount	Tightening torque	20 Nm (15 ft. lb.)
Fastening screws	Heat shield to front-axle carrier	Tightening torque	9 Nm (6.5 ft. lb.)
Fastening screw	Heat shield to front-axle carrier	Tightening torque	20 Nm (15 ft. lb.)
Fastening screws	Heat shield over engine mount	Tightening torque	20 Nm (15 ft. lb.)
Fastening screws	Retainer plate to front-axle carrier	Tightening torque	30 Nm (22 ft. lb.)
Fastening screw	Step 1, engine mount	Initial tightening	90 Nm (67 ft. lb.)
Fastening screw	Step 2, engine mount	Final tightening	+90°
Fastening screw	Step 1, front-axle carrier to body	Initial tightening	115 Nm (85 ft. lb.)
Fastening screw	Step 2, front-axle carrier to body	Final tightening	+90°
Fastening screw	Step 1, front-axle carrier to body	Initial tightening	115 Nm (85 ft. lb.)
Fastening screw	Step 2, front-axle carrier to body	Final tightening	+90°
Fastening screws	Engine mount to front-axle carrier	Tightening torque	55 Nm (41 ft. lb.)
Fastening screws	Step 1, cross-strut to front-axle carrier	Initial tightening	90 Nm (67 ft. lb.)
Fastening screws	Step 2, cross-strut to front-axle carrier	Final tightening	+135°
Front fastening screw	Step 1, cross-strut to front-axle carrier	Initial tightening	90 Nm (67 ft. lb.)
Fastening screw	Step 2, Cross-strut to front-axle carrier	Final tightening	+90°
Fastening screw	Step 1, fastening screw for connecting link	Initial tightening	40 Nm (30 ft. lb.)
Fastening screw	Step 2, fastening screw for connecting link	Final tightening	+90°
Fastening screw	Step 1, fastening screw for connecting link	Initial tightening	40 Nm (30 ft. lb.)
Fastening screw	Step 2, fastening screw for connecting link	Final tightening	+90°
Fastening nut		Tightening torque	25 Nm (19 ft. lb.)
Fastening screw	Protective plate	Tightening torque	20 Nm (15 ft. lb.)