Technical values
WARNING: This page is about a different car, the 2015 Porsche Macan. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATION
| Location | Description | Type | Basic value | Tolerance 1 | Tolerance 2 |
|---|---|---|---|---|---|
| Screw, M4 8.8 | Tightening torque | 3 Nm (2 ft lb.) | |||
| Screw, M4 10.9 | Tightening torque | 4 Nm (3 ft lb.) | |||
| Screw, M4 12.9 | Tightening torque | 5 Nm (3.5 ft lb.) | |||
| Screw, M5 8.8 | Tightening torque | 6 Nm (4.5 ft lb.) | |||
| Screw, M5 10.9 | Tightening torque | 8 Nm (6 ft lb.) | |||
| Screw, M5 12.9 | Tightening torque | 10 Nm (7.5 ft lb.) | |||
| Screw, M6 8.8 | Tightening torque | 10 Nm (7.5 ft lb.) | |||
| Screw, M6 10.9 | Tightening torque | 13 Nm (9.5 ft lb.) | |||
| Screw, M6 12.9 | Tightening torque | 16 Nm (12 ft lb.) | |||
| Screw, M8 8.8 | Tightening torque | 23 Nm (17 ft lb.) | |||
| Screw, M8 10.9 | Tightening torque | 33 Nm (24 ft lb.) | |||
| Screw, M8 12.9 | Tightening torque | 39 Nm (29 ft lb.) | |||
| Screw, M10 8.8 | Tightening torque | 45 Nm (33 ft lb.) | |||
| Screw, M10 10.9 | Tightening torque | 65 Nm (48 ft lb.) | |||
| Screw, M10 12.9 | Tightening torque | 80 Nm (59 ft lb.) | |||
| Screw, M10 x 1.25 8.8 | Tightening torque | 50 Nm (37 ft lb.) | |||
| Screw, M10 x 1.25 10.9 | Tightening torque | 70 Nm (52 ft lb.) | |||
| Screw, M10 x 1.25 12.9 | Tightening torque | 85 Nm (63 ft lb.) | |||
| Screw, M12 8.8 | Tightening torque | 80 Nm (59 ft lb.) | |||
| Screw, M12 10.9 | Tightening torque | 115 Nm (85 ft lb.) | |||
| Screw, M12 12.9 | Tightening torque | 135 Nm (100 ft lb.) | |||
| Screw, M12 x 1.25 8.8 | Tightening torque | 90 Nm (67 ft lb.) | |||
| Screw, M12 x 1.25 10.9 | Tightening torque | 125 Nm (93 ft lb.) | |||
| Screw, M12 x 1.25 12.9 | Tightening torque | 150 Nm (111 ft lb.) | |||
| Screw, M12 x 1.5 8.8 | Tightening torque | 85 Nm (63 ft lb.) | |||
| Screw, M12 x 1.5 10.9 | Tightening torque | 120 Nm (89 ft lb.) | |||
| Screw, M12 x 1.5 12.9 | Tightening torque | 145 Nm (107 ft lb.) | |||
| Screw, M14 8.8 | Tightening torque | 130 Nm (96 ft lb.) | |||
| Screw, M14 10.9 | Tightening torque | 180 Nm (133 ft lb.) | |||
| Screw, M14 12.9 | Tightening torque | 220 Nm (163 ft lb.) | |||
| Screw, M16 8.8 | Tightening torque | 200 Nm (148 ft lb.) | |||
| Screw, M16 10.9 | Tightening torque | 280 Nm (207 ft lb.) | |||
| Screw, M16 12.9 | Tightening torque | 335 Nm (248 ft lb.) | |||
| Aluminum screw, M6 | AL9 | Initial tightening | 4 Nm (3 ft lb.) | ||
| Aluminum screw, M6 | AL9 | Final tightening | 90° | ||
| Aluminum screw, M8 | AL9 | Initial tightening | 10 Nm (7.5 ft lb.) | ||
| Aluminum screw, M8 | AL9 | Final tightening | 90° | ||
| Aluminum screw, M10 | AL9 | Initial tightening | 20 Nm (15 ft lb.) | ||
| Aluminum screw, M10 | AL9 | Final tightening | 90° | ||
| Fastening screw securing fuel tank to body | Tightening torque | 20 Nm (15 ft lb.) | |||
| Fastening screw securing tank filler neck to wheel housing | M8 x 25 | Tightening torque | 15 Nm (11 ft lb.) | ||
| Stone guard to fuel tank | Nut, M8 | Tightening torque | 20 Nm (15 ft lb.) | ||
| Fastening screw securing carbon canister to body | M8 x 30 | Tightening torque | 15 Nm (11 ft lb.) | ||
| Fuel pump control unit to body | Plastic nut | Tightening torque | 8 Nm (6 ft lb.) | ||
| Stud to body | Tightening torque | 15 Nm (11 ft lb.) | |||
| Fastening nut securing suspension to body | Tightening torque | 20 Nm (15 ft lb.) | |||
| Fastening nuts securing air cleaner for carbon canister to wheel arch | Nut, M6 | Tightening torque | 5 Nm (3.5 ft lb.) | ||
| Fastening screw securing fuel line cover to body | M6 x 12 | Tightening torque | 8 Nm (6 ft lb.) | ||
| Accelerator pedal module to pedals | M6 x 18 | Tightening torque | 8 Nm (6 ft lb.) | ||
| Fastening nut securing exhaust manifold/turbocharger to cylinder head | Replace | Initial tightening | 20 Nm (15 ft lb.) | ||
| Fastening nut securing exhaust manifold/turbocharger to cylinder head | Final tightening | 27 Nm (20 ft lb.) | |||
| Fastening nut securing heat shield to exhaust manifold/turbocharger | Tightening torque | 10 Nm (7.5 ft lb.) | |||
| Fastening nut securing exhaust manifold/turbocharger to cylinder head | Replace | Initial tightening | 20 Nm (15 ft lb.) | ||
| Fastening nut securing exhaust manifold/turbocharger to cylinder head | Final tightening | 27 Nm (20 ft lb.) | |||
| Fastening nut securing heat shield to exhaust manifold/turbocharger | Tightening torque | 10 Nm (7.5 ft lb.) | |||
| Fastening nut for exhaust manifold/turbocharger | Initial tightening | 20 Nm (15 ft lb.) | |||
| Fastening nut for exhaust manifold/turbocharger | Final tightening | 27 Nm (20 ft lb.) | |||
| Fastening screw for oil line | Tightening torque | 10 Nm (7.5 ft lb.) | |||
| Fastening screw securing oil extraction line to upper part of oil pan | Tightening torque | 10 Nm (7.5 ft lb.) | |||
| Fastening screw securing oil feed line to turbocharger | Tightening torque | 10 Nm (7.5 ft lb.) | |||
| Fastening screw for oil line | Tightening torque | 10 Nm (7.5 ft lb.) | |||
| Fastening screw securing oil extraction line to upper part of oil pan | Tightening torque | 10 Nm (7.5 ft lb.) | |||
| Fastening screw securing oil feed line to turbocharger | Tightening torque | 10 Nm (7.5 ft lb.) | |||
| Fastening screw for pressure pipe | 6 x 35 with washer, 28 mm | Tightening torque | 3 Nm (2 ft lb.) | ||
| Fastening screw securing ambient air connection to charge-air cooler | Tightening torque | 4 Nm (3 ft lb.) | |||
| Fastening screw for charge-air cooler | M6 x 35 | Tightening torque | 7 Nm (5 ft lb.) | ||
| Screw-type clamps on intake and boost pressure lines | Tightening torque | 5.5 Nm (4 ft lb.) | |||
| Fastening screws | Air cleaner housing cover to air cleaner housing | Tightening torque | 3.5 Nm (2.5 ft lb.) | ||
| Fastening screws | Air cleaner housing to body | Tightening torque | 3.5 Nm (2.5 ft lb.) | ||
| Fastening bolt | Fastening bolt on air guide | Torque angle | 90° | ||
| Fastening screw securing pressure and temperature sensor to intake system | Tightening torque | 3 Nm (2 ft lb.) | |||
| Fastening screw securing heat socket for positive crankcase ventilation to intake system | Tightening torque | 3 Nm (2 ft lb.) | |||
| Fastening screw securing throttle valve to intake system | Tightening torque | 6.5 Nm (5 ft lb.) | +1 Nm (+0.5 ft lb.) | ||
| Fastening screw for intake-air distributor | Shouldered bolt | Tightening torque | 10 Nm (7.5 ft lb.) | ||
| Fastening screw for intake-air distributor | Tightening torque | 10 Nm (7.5 ft lb.) | |||
| Fastening screw for fuel collection pipe | Tightening torque | 10 Nm (7.5 ft lb.) | |||
| High-pressure sensor in fuel collection pipe | Tightening torque | 20 Nm (15 ft lb.) | |||
| Stopper for fuel collection pipe | Tightening torque | 25 Nm (19 ft lb.) | |||
| Screw for clamp | Tightening torque | 10 Nm (7.5 ft lb.) | |||
| Union nuts for high-pressure lines | After opening the conical/ball joints, always replace high-pressure line with the latest type | Initial tightening | 8 Nm (6 ft lb.) | ||
| Union nuts for high-pressure lines | After opening the conical/ball joints, always replace high-pressure line with the latest type | Final tightening | +50° | ||
| Fastening screw for high-pressure pump | Tightening torque | 10 Nm (7.5 ft lb.) | |||
| Fastening screw for low-pressure line | Tightening torque | 10 Nm (7.5 ft lb.) | |||
| Fuel pressure sensor (low-pressure sensor) | Tightening torque | 20 Nm (15 ft lb.) | |||
| Fastening screw with guide sleeve for vacuum reservoir to crankcase | Tightening torque | 10 Nm (7.5 ft lb.) | |||
| Oxygen sensor | Coat oxygen sensor thread with assembly grease 000.043.207.07 | Tightening torque | 55 Nm (41 ft lb.) | ||
| Fastening nut securing rear silencer to body | M8 | Tightening torque | 20 Nm (15 ft lb.) | ||
| Clamping sleeve, D65 | Tightening torque | 33 Nm (24 ft lb.) | +/-5 Nm (+/-3.5 ft lb.) | ||
| Fastening nut securing front silencer to catalytic converter | M8/replace | Tightening torque | 23 Nm (17 ft lb.) | ||
| Fastening screw for catalytic converter support | M8 x 20 | Tightening torque | 23 Nm (17 ft lb.) | ||
| V-band clamp, 107 | Tightening torque | 13 Nm (9.5 ft lb.) | |||
| V-band clamp, 96 | Tightening torque | 13 Nm (9.5 ft lb.) | |||
| Fastening nuts securing intermediate pipe to turbocharger | MX | Tightening torque | 23 Nm (17 ft lb.) | ||
| Fastening screw securing compression spring to tab | M8 x 50 | Tightening torque | 23 Nm (17 ft lb.) | ||
| Fastening screws securing bracket to transmission | Tightening torque | 23 Nm (17 ft lb.) | |||
| Fastening screw securing rubber stop to bracket | M8 x 30 | Tightening torque | 23 Nm (17 ft lb.) | ||
| Fastening screw securing rear silencer at the rear to body | M8 x 40 | Tightening torque | 20 Nm (15 ft lb.) | ||
| Fastening screw securing tailpipe cover to tailpipe | M6x 12 | Tightening torque | 8 Nm (6 ft lb.) | ||
| Fastening nut on connecting strut for rear silencer | M8 | Tightening torque | 23 Nm (17 ft lb.) | ||
| Fastening nut securing rear silencer to body | M8 | Tightening torque | 20 Nm (15 ft lb.) | ||
| Clamping sleeve, D65 | Tightening torque | 30 Nm (22 ft lb.) | +/-5 Nm (+/-3.5 ft lb.) | ||
| Fastening nut securing front silencer to catalytic converter | M8/replace | Tightening torque | 23 Nm (17 ft lb.) | ||
| Fastening screw for catalytic converter support | M8 x 20 | Tightening torque | 23 Nm (17 ft lb.) | ||
| V-band clamp, 107 | Tightening torque | 13 Nm (9.5 ft lb.) | |||
| V-band clamp, 96 | Tightening torque | 13 Nm (9.5 ft lb.) | |||
| Fastening nuts securing intermediate pipe to turbocharger | MX | Tightening torque | 23 Nm (17 ft lb.) | ||
| Fastening screw securing compression spring to tab | M8 x 50 | Tightening torque | 23 Nm (17 ft lb.) | ||
| Fastening screws securing bracket to transmission | Tightening torque | 23 Nm (17 ft lb.) | |||
| Fastening screw securing rubber stop to bracket | M8 x 30 | Tightening torque | 23 Nm (17 ft lb.) | ||
| Fastening screw securing rear silencer at the rear to body | M8 x 40 | Tightening torque | 20 Nm (15 ft lb.) | ||
| Fastening screw securing tailpipe cover to tailpipe | M6 x 12 | Tightening torque | 8 Nm (6 ft lb.) | ||
| Fastening nut on connecting strut for rear silencer | M8 | Tightening torque | 23 Nm (17 ft lb.) | ||
| Screw for exhaust flap actuator | Tightening torque | 5 Nm (3.5 ft lb.) | |||
| Fastening screw securing secondary-air pump holder to vacuum reservoir | Tightening torque | 8 Nm (6 ft lb.) | |||
| Fastening screw for starter | Tightening torque | 45 Nm (33 ft lb.) | +8 Nm (+6 ft lb.) | ||
| Fastening nut securing B+ line to starter | Tightening torque | 18 Nm (13 ft lb.) | |||
| Fastening nut securing terminal 50 line to starter | Tightening torque | 10 Nm (7.5 ft lb.) | |||
| Fastening screw for generator | M8x 100 | Tightening torque | 23 Nm (17 ft lb.) | ||
| Fastening nut securing B+ line to generator | M8 | Tightening torque | 23 Nm (17 ft lb.) | ||
| Holder for distance measuring sensor control unit to closing panel | Internal Torx screw, M6 x 12 | Tightening torque | 8 Nm (6 ft lb.) | ||
| Holder for distance measuring sensor control unit, lower to plastic bracket | Internal Torx screw, 0 5 x 16 | Tightening torque | 2.5 Nm (2 ft lb.) | ||
| Terminal clamp to battery terminal | M6 nut | Tightening torque | 5 Nm (3.5 ft lb.) | ||
| Ground line for battery to body | Cap nut, M8 | Tightening torque | 18 Nm (13 ft lb.) | ||
| Clamp support for battery to body | Hexagon-head bolt, M8 x 25 | Tightening torque | 23 Nm (17 ft lb.) | ||
| Spark plug NEW | Initial tightening/do not use lubricant | Tightening torque | 30 Nm (22 ft lb.) | +1.5 Nm (+1 ft lb.) | |
| Spark plug | Re-tightening/do not use lubricant | Tightening torque | 25 Nm (19 ft lb.) | +1.5 Nm (+1 ft lb.) | |
| Electrode gap of spark plug | Control value | 0.7 mm | +0.1 mm | ||
| Fastening screw for ignition coil | M6 x 45 | Tightening torque | 10 Nm (7.5 ft lb.) | ||
| Fastening screw for knock sensor | Tightening torque | 23 Nm (17 ft lb.) | |||
| Fastening screw securing phase sensor to cylinder head | M6 x 16 AL9/replace | Initial tightening | 4 Nm (3 ft lb.) | ||
| Fastening screw securing phase sensor to cylinder head | Final tightening | +60° | |||
| Fastening screw for hydraulic valve for valve lift control | Tightening torque | 6 Nm (4.5 ft lb.) | |||
| Cover on fuse box in plenum panel | Internal Torx screw, | Tightening torque | 3.5 Nm (2.5 ft lb.) | ||
| Fastening screw for crankshaft pulse sender | Tightening torque | 10 Nm (7.5 ft lb.) |