Group 13, Crankshaft Belt Drive

WARNING: This page is about a different car, the 2014 Porsche Cayenne, 2013 Porsche Cayenne, 2012 Porsche Cayenne, and 2011 Porsche Cayenne. However, it is still accessible from the selected car via links, so may be relevant.

Fig 1: Crankshaft Components Location

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Crankshaft

1	Crankshaft
2	Straight pin, 6 x 20
3	Spring, 5 x 6.5
4	Thrust washer (grooves facing out)
5	Main bearing shell, upper
6	Main bearing shell, lower
7	Shaft sealing ring => Do not touch sealing ring lip! Clean crankshaft flange and oil lightly
8	View of crankshaft flange
9	Crankshaft bearing classification (four types) G Yellow; B Blue, R Red; N Green => (example: GGGGG-BBBB; 5 main shaft bearings with yellow marking, 4 double (8) connecting rod bearings with blue marking) => For numbering, see A
A	Direction of travel (main bearing 1 is the first in direction of travel against output)

Fig 2: Belt Drive Components Location With Torque Specification

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Belt drive

1	Deflection roller > Tightening torque 32 (24 ft lb.) Nm
2	Hydraulic belt tensioner; tensioner to lever > Tightening torque 32 (24 ft lb.) Nm ; tensioning roller to tensioning lever > Tightening torque 32 (24 ft lb.) Nm
3	Screw, M8 x 96; complete lever to chain housing cover and cylinder head > Tightening torque 32 (24 ft lb.); Nm belt tensioner and timing chain housing cover to bracket > Tightening torque 32 (24 ft lb.) Nm
4	Deflection roller > Tightening torque 32 (24 ft lb.) Nm
5	Dual poly V-belt

Fig 3: Piston, Connecting Rod Components Location With Torque Specification

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Piston, connecting rod

1	Piston-ring set; oil with engine oil; TOP marking facing upwards; oil scraper ring down; ring gaps offset by 120°
2	Piston; different on naturally aspirated and turbo engines; combustion chamber recess facing centre of engine; left and right different; direction of travel arrow in direction of travel
3	Piston-pin circlip (positioned at 6 o'clock or 11 o'clock)
4	Piston pin; oil
5	Connecting rod
6	Connecting rod bolt; replace as it must be tightened in the plastic area; oil screw > Tightening torque 8 (6 ft lb.) Nm > Tightening torque 20 (15 ft lb.) Nm > Tightening torque 40 (30 ft lb.) Nm > Torque angle 90°
7	Connecting rod bearing shells; oil with engine oil

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Connecting-rod assembly, bearing shells

A	View A (identification area for connecting-rod number; fit connecting rod with identification area facing exhaust side; markings on rod and cap must be on the same side)
B	View B (fit bearing shells flush and press in by hand) Information Twist lock for bearing shells always on the same side.
C	View C (fit bearing shells flush and press in by hand)

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Piston classification, naturally aspirated engine

1	Marking for dimension group (just one permitted per engine, in this case x)
2	Porsche short numeric code without main or middle number
3	Short numeric code (supplier)
4	Marking area for weight group (just one permitted per engine, + or -)
5	Cylinder bank identification (V6 1-3 and 4-6) (V8 1-4 and 5-8)
6	Barcode 128 (short numeric code without main group or weight group)
7	Arrow marking in direction of travel
8	Identification for dimension group
9	Arrow marking in direction of travel
10	Inspection stamp (supplier)

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Piston classification, turbo engine

1	Arrow marking in direction of travel
2	Porsche short numeric code without main or middle number
3	Short numeric code (supplier)
4	Cylinder bank identification (V8 1-4 and 5-8)
5	Marking area for weight group (just one permitted per engine, + or -)
6	Barcode 128 (short numeric code without main group or weight group)
7	Arrow marking in direction of travel
8	Marking for dimension group (just one permitted per engine, in this case x)
9	Marking area for weight group (just one permitted per engine, + or -)
10	Inspection stamp (supplier)

Fig 4: Radial Shaft Seal Components Location

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Radial shaft seal

1	Radial shaft seal (use protection cap for radial shaft seal for fitting; only fit when crankcase is screwed on)
2	Crankcase
3	Crankshaft
4	Radial shaft seal (sectional view)
A	Direction of travel

Fig 5: Pulleys Components Location With Torque Specification

Courtesy of PORSCHE CARS NORTH AMERICA, INC.

Pulleys

1	Water pump pulley
2	Screw, M8 x 16 > Tightening torque 23 (17 ft lb.) Nm
3	Vibration damper
4	Screw, M18 x 1.5 x 72; use new screw; > Tightening torque 20 (15 ft lb.) Nm > Tightening torque 50 (37 ft lb.) Nm > Tightening torque 100 (74 ft lb.) Nm > Torque angle 180°
5	Pulley on power-steering pump
6	Screw, M8 x 16 > Tightening torque 23 (17 ft lb.) Nm
7	Tandem pump pulley