Technical Values: Notes

Location	Description	Type	Basic value	Tolerance 1	Tolerance 2
Fastening screw for ventilation duct	Item 1	Tightening torque	5.5 Nm (4 ftlb.)
Securing ventilation duct
Fastening screw for armrest extension	Item 2	Tightening torque	5.5 Nm (4 ftlb.)
Positioning armrest extension
Fastening screw securing upper part to B-pillar	Item 5	Tightening torque	5.5 Nm (4 ftlb.)
Securing trim panel at the top
Fastening screws securing front part of trim panel for C-pillar	Item 8/top	Tightening torque	1.7 Nm
Securing front part of C-pillar trim panel
Fastening screws securing front part of trim panel for C-pillar	Item 8/bottom	Tightening torque	1.7 Nm
Securing front part of C-pillar trim panel at the bottom
Fastening screw securing belt fitting to body		Tightening torque	50 Nm (37 ftlb.)
Securing belt fitting
Fastening screw for backrest panel	Item 1	Tightening torque	10 Nm (7.5 ftlb.)	+/-1 Nm (+/- 0.5 ftlb.)
Securing backrest side panel
Fastening screw for armrest extension	Item 3	Tightening torque	5.5 Nm (4 ftlb.)
Securing armrest extension
Fastening screw securing rear part of trim panel for C-pillar		Tightening torque	5.5 Nm (4 ftlb.)
Securing rear part of C-pillar trim panel
Bolt for roll-up sunblind		Tightening torque	12 Nm
Screwing in bolt for roll-up sunblind
Fastening screw securing trim panel for A-pillar	Item 2	Tightening torque	4.5 Nm
Securing A-pillar at the top
Fastening screws for door panel	Item 1	Tightening torque	7.5 Nm
Installing door panel
Trim for door panel		Tightening torque	3 Nm
Securing trim for door panel
Fastening screw for door panel	Item 1	Tightening torque	7.5 Nm
Installing door panel
Fastening screw for lashing point		Tightening torque	9.7 Nm +/-1 Nm (+/- 0.5 ftlb.)
Installing lashing point
Fastening screws securing luggage compartment trim at the sides		Tightening torque	1.5 Nm (1 ftlb.)
Securing side trim panel for rear luggage compartment
Fastening screws for lock carrier trim panel		Tightening torque	1.5 Nm (1 ftlb.)
Securing rear luggage compartment cover
Fastening screw securing luggage compartment side trim panel		Tightening torque	1.5 Nm (1 ftlb.)
Securing side trim panel at the front
Fastening screw for centre and rear luggage compartment side trim panel		Tightening torque	1.5 Nm (1 ftlb.)
Securing rear side trim panel
Fastening screws for switch panel		Tightening torque	3.2 Nm
Tightening fastening screws
Lateral fastening screws	Item 4	Tightening torque	3.2 Nm
Tightening lateral fastening screws
Cover to switch panel		Tightening torque	3.2 Nm	+/-0.5 Nm (+/- 0.5 ftlb.)
Installing cover on driver's side
Fastening screws to trim panel	Torx screw	Tightening torque	3.2 Nm
Transverse strut to trim panel	Hexagon-head bolt	Tightening torque	8.0 Nm (6 ftlb.)
Fitting trim panel to transverse strut
Fastening screw securing trim panel to lid		Tightening torque	5 Nm	+/-1 Nm (+/- 0.5 ftlb.)
Unscrewing fastening screws
Fastening screw for finger plate		Tightening torque	5 Nm	+/-1 Nm (+/- 0.5 ftlb.)
Unscrewing fastening screws under the finger plate
Fastening screw securing pedestrian protection strip to lock carrier	For new lock carrier	Tightening torque	13 Nm	+1 Nm (+0.5 ftlb.)	-2 Nm (- 1.5 ftlb.)
Removing front apron holder
Fastening screw securing pedestrian protection strip to lock carrier	When re-using old screws	Tightening torque	9.7 Nm	+1 Nm (+0.5 ftlb.)	-1.5 Nm (-1 ftlb.)
Removing front apron holder
Fastening screw securing holder to lock carrier	For new lock carrier	Tightening torque	13 Nm	+1 Nm (+0.5 ftlb.)	-2 Nm (- 1.5 ftlb.)
Installing front apron holder
Fastening screw securing holder to lock carrier	When re-using old screws	Tightening torque	9.7 Nm	+1 Nm (+0.5 ftlb.)	1.5 Nm (1 ftlb.)
Installing front apron holder
Folding table to adjustment mechanism	Item 1	Tightening torque	16 Nm (12 ftlb.)
Loosening fastening screws
Backrest frame to seat frame	Item 1	Tightening torque	35 Nm (26 ftlb.)	+/-4 Nm (+/- 3 ftlb.)
Fitting fastening screws
Support to backrest frame	Item 1	Tightening torque	7.5 Nm (5.5 ftlb.)	+/-1 Nm (+/- 0.5 ftlb.)
Securing support for backrest side bolster
Cover for table top Item 3		Tightening torque	2.5 Nm (2 ftlb.)
Securing lower table cover
Locking mechanism to backrest frame		Tightening torque	3.2 Nm (2 ftlb.)
Tightening fastening screws on locking mechanism
Locking mechanism to backrest frame		Tightening torque	5 Nm (3.5 ftlb.)
Installing retaining bracket
Bearing pins on backrest frame	Items 1 and 2	Tightening torque	50 Nm (37 ftlb.)	+/-5 Nm (+/- 3.5 ftlb.)
Tightening bearing pins
Bearing pins on backrest frame	Items 1 and 2	Tightening torque	50 Nm (37 ftlb.)	+/-5 Nm (+/- 3.5 ftlb.)
Tightening bearing pins
Bearing pins on backrest frame	Items 1 and 2	Tightening torque	50 Nm (37 ftlb.)	+/-5 Nm (+/- 3.5 ftlb.)
Tightening bearing pins
Lock to backrest frame		Tightening torque	23 Nm (17 ftlb.)	+/-2.5 Nm (+/- 2 ftlb.)
Tightening fastening screws for lock
Fastening screw for seat-surface extension	Item 1	Tightening torque	6.5 Nm (5 ftlb.)	+/-0.5 Nm (+/- 0.5 ftlb.)
Removing fastening screws at the bottom
Fastening screw for seat-surface extension	Item 2	Tightening torque	6.5 Nm (5 ftlb.)	+/-0.5 Nm (+/- 0.5 ftlb.)
Removing fastening screws at the top
Fastening screw for seat-surface extension, rear	Item 2	Tightening torque	10 Nm (7.5 ftlb.)	+/-1 Nm (+/- 0.5 ftlb.)
Tightening fastening nuts
Lock for load-through provision	Item 2	Tightening torque	20 Nm (15 ftlb.)	+/-2 Nm (+/- 1.5 ftlb.)
Tightening fastening screws for lock
Fastening screws for folding table	Item 3	Tightening torque	16 Nm (12 ftlb.)
Installing folding table
Fastening screw securing front seat to front seat frame	Item 2	Tightening torque	50 Nm (37 ftlb.)	+/-5 Nm (+/- 3.5 ftlb.)
Tightening front fastening screws
Fastening screw securing front seat to rear seat frame	Item 1	Tightening torque	50 Nm (37 ftlb.)	+/-5 Nm (+/- 3.5 ftlb.)
Tightening rear fastening screws