LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2016 >> Macan Turbo >> Repair and Diagnosis >> External Pages >> Different car >> Section 620 (37 Automatic Transmission - Actuator, Housing -- (95B) MACAN) >> WM 370235 Checking And Topping Up ATF (Except MACAN Sport Edition) >> Checking And Topping Up ATF >> Notes

Checking And Topping Up ATF: Notes

WARNING: This page is about a different car, the 2018 Porsche Macan and 2017 Porsche Macan. However, it is still accessible from the selected car via links, so may be relevant.
WARNING: Hot fluid
  • Danger of scalding

→ Let the fluid cool down.

→ Wear personal protective gear.

NOTE: Dirt and contamination
  • Risk of damage to units or components

→ Protect components from dirt and contamination.

→ Clean or replace dirty components.

NOTE: Fill level too low
  • Risk of damage to components.

→ Do not start the engine.

→ Do not tow the vehicle.

NOTE:

Only use oil approved by Porsche in the Porsche Doppelkupplung (PDK), see Parts Catalogue.

NOTE:
  • Read out the ATF temperature using PIWIS Tester II9818. 
  • The ATF temperature must not be higher than 30 °C at the beginning of the ATF test. 
  • The ATF level changes as the ATF temperature changes. 
  • Perform ATF test when the engine running and selector lever in position P. 
  • An ATF test performed when the ATF temperature is too low will result in overfilling. 
  • An ATF test performed when the temperature is too high will result in insufficient filling. 
  • An ATF level that is too high or too low will impair the function of the transmission. 
NOTE:
  • The ATF level is checked at the ATF inspection plug. 
  • The ATF level is correct if a small amount of fluid still emerges at the ATF inspection plug at an ATF temperature of between 30° and 50 °C. 
NOTE:

Always pay particular attention to the following before raising the vehicle:

  • Deactivate the levelling system before raising the vehicle (press and hold the levelling system button for at least 10 seconds). 
  • If a transmission range is engaged while the vehicle is raised, the levelling system must first be deactivated using PIWIS Tester II 9818  . To do this, select >>Levelling system/PASM<<>>Drive links/checks<<>>Activate/deactivate levelling system (without wheel rotation detection)<< in the control unit overview. Select the value "Deactivate levelling system (permanently)" and press "Start" [F8] to execute the function. Re-activate the levelling system when the work is complete. To do this, select >>Drive links/checks<<>>Conclude initial commissioning>> and then select "Activate levelling system" under >>Activate/deactivate levelling system (without wheel rotation detection)<< and execute the function by pressing "Start" [F8].
  • All functions (e.g. ventilation/filling) of the PASM control unit are deactivated as soon as the levelling system has been deactivated using the function >>Activate/deactivate levelling system (without wheel rotation detection)<<. 
NOTE:
  • The ATF inspection plug must be closed again at 50 °C at the latest. 
  • Switch off the engine if necessary, let the transmission cool down and repeat the test. 
  1. Read off the ATF temperature on the PIWIS Tester while the engine is running.
  2. Leave engine running at idle speed.
  3. Place oil collection pan underneath.
  4. Fill manual metering pump Manual metering pumps, Porsche set WE 1372  with ATF for the Porsche Doppelkupplung (PDK).
  5. Check and top up ATF.
    1. 5.1. When an ATF temperature of 30 °C is reached, unscrew the ATF inspection plug -arrow-  .
    2. 5.2. If ATF emerges from the ATF control opening before the ATF temperature has reached 40 °C, the ATF level is OK.
    3. 5.3. If no ATF emerges at a temperature of up to 40 °C, add ATF using the manual metering pump until ATF emerges.
      G11983423

      ATF inspection plug

  6. Screw in and tighten new  ATF inspection plug with a new  sealing ring. Tightening torque 60 Nm (44 ftlb.) 
scientia non olet · About LEMON Manuals