Intake-Air Distributor, Air Cleaner
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2019 Porsche 911, 2018 Porsche 911, 2017 Porsche 911, 2016 Porsche 911, and 2015 Porsche 911. However, it is still accessible from the selected car via links, so may be relevant.
| Location | Description | Type | Basic value | Tolerance 1 | Tolerance 2 |
|---|---|---|---|---|---|
| Intake-air distributor to cylinder head | External Torx screw, M6 x 35 | Tightening torque | 13 Nm (9.5 ftlb.) | ||
| Intake-air distributor to intake manifold (X51) | Screw, M6 x 30 | Tightening torque | 13 Nm (9.5 ftlb.) | +/-2 Nm (+/-1.5 ftlb.) | |
| Intake manifold (X51) to cylinder head | Screw, M6 x 25 | Tightening torque | 13 Nm (9.5 ftlb.) | ||
| Holder to intake-air distributor and intake manifold (X51) | M6 screw | Tightening torque | 10 Nm (7.5 ftlb.) | ||
| Connecting holder for intake-air distributor/resonance tube (X51) | M6 screw | Tightening torque | 6 Nm (4.5 ftlb.) | +1 Nm (+0.5 ftlb.) | |
| Oil filler hose connection piece to intake-air distributor, bank 1-3 (X51) | Screw, M6 x 16 | Tightening torque | 10 Nm (7.5 ftlb.) | ||
| Clamp for resonance tube | Internal Torx screw, M6 x 35 - micro-self-locking - replace screws | Tightening torque | 4.5 Nm (3 ftlb.) | ||
| Positive crankcase ventilation holder to intake-air distributor | External Torx screw, M6 x 12 (2x) | Tightening torque | 10 Nm (7.5 ftlb.) | ||
| Vacuum unit to resonance tube | Self-tapping screw | Tightening torque | 5 Nm (3.5 ftlb.) | ||
| Tank vent valve holder to intake-air distributor | External Torx screw, M6 x 12 (2x) | Tightening torque | 10 Nm (7.5 ftlb.) | ||
| Intake manifold pressure sensor to intake-air distributor | Oval-head screw, 6.0 x 15 | Tightening torque | 5 Nm (3.5 ftlb.) | ||
| Throttle housing to intake-air distributor | External Torx screw, M6 x 50 | Tightening torque | 10 Nm (7.5 ftlb.) | ||
| Throttle housing to resonance tube (X51) | Screw, M6 x 45 | Tightening torque | 10 Nm (7.5 ftlb.) | ||
| Cable duct to intake-air distributor | External Torx screw, M6 x 16 | Tightening torque | 13 Nm (9.5 ftlb.) | ||
| Rubber shroud to throttle body | Screw-type clamp | Tightening torque | 3 Nm (2 ftlb.) | ||
| Air cleaner housing to body | Hexagon-head bolt with washer, M6 x 25 | Tightening torque | 7 Nm (5 ftlb.) | ||
| Air cleaner housing cover | Self-tapping screw | Tightening torque | 3 Nm (2 ftlb.) | ||
| DME control unit holder to body | M6 collar nut | Tightening torque | 9 Nm (6.5 ftlb.) | ||
| Intake manifold pressure sensor to resonance tube (X51) | Screw, M5 x 16 | Tightening torque | 5 Nm (3.5 ftlb.) | ||
| Vacuum unit to resonance tube (X51) | Screws M5 x 16 | Tightening torque | 5 Nm (3.5 ftlb.) | ||
| Vacuum unit to intake manifold/flap module (X51) | M5 nut, self-locking | Tightening torque | 5 Nm (3.5 ftlb.) | +/-1 Nm (+/-0.5 ftlb.) | |
| Flap module to intake manifold (X51) | Screw, M5 x 12 | Tightening torque | 7 Nm (5 ftlb.) | +/-1 Nm (+/-0.5 ftlb.) | |
| Holder for wire harness for intake manifold 1-3, front | Screw, M6 x 12 | Tightening torque | 10 Nm (7.5 ftlb.) |