LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2016 >> Macan S >> Repair and Diagnosis >> External Pages >> Different car >> Section 646 (94 Lights, Lamps, Switches, Exterior -- (95B) MACAN) >> WM 944955 Replacing Control Unit For Front-End Electronics (Except MACAN Sport Edition) >> Replacing control unit for front-end electronics

Replacing control unit for front-end electronics

WARNING: This page is about a different car, the 2018 Porsche Macan and 2017 Porsche Macan. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
  • All remote controls (keys) are required for teaching a DME, front-end electronics (front BCM), rear-end electronics (rear BCM), electronic steering lock (ELV) control unit for example, or for teaching remote controls (keys).
  • Remote controls (keys) that are not taught during this procedure will no longer be recognized by the vehicle.
CAUTION: Voltage drop
  • Risk of irreparable damage to control unit
  • Risk of damage to control unit
  • Fault entries in the control unit
  • Coding in the control unit is aborted
  • Malfunctions in control unit, even during programming

→ Prior to disconnecting the control unit, switch off ignition and remove ignition key.

→ Ensure that the power supply is not interrupted during programming.

→ Connect a battery charger with a current rating of at least → Nominal value: 40 A  to the vehicle battery.

NOTE:

The PIWIS Tester 3 9900  instructions take precedence since the description may be different with later Tester releases.

The procedure described here has been structured in general terms; different text or additions may appear in PIWIS Tester 3 9900  .

  1. PIWIS Tester II 9818  must be connected to the vehicle before starting the Tester. Switch on ignition.
  2. Select the vehicle type and start the diagnostic application.
  3. Select Front-end electronics  .
  4. Extended identification  must now be selected.
  5. Enter the vehicle identification number  and press [Enter] to confirm your entry.
  6. Maintenance/repairs  must then be selected.
  7. Control unit replacement  must now be selected. Then press [F12] to continue.
  8. Select Write values  and press [F12] to continue.
  9. Press [F8] to start writing values.
  10. When a message appears confirming that the values were written and coded successfully  , press [F12] to continue.
  11. Go back to the Start page on the Tester.
  12. To activate the control units, switch on the hazard warning lights.
  13. Select the menu Diagnostics --> Online teaching function --> Engine immobiliser  on the Start page.
  14. Vehicle  must now be selected. Then press [F12] to continue. Vehicle data will be read out.
  15. Follow the instructions on the Tester.
  16. The vehicle identification number (VIN) is displayed. Change the vehicle identification number if necessary.
  17. Enter the repair order number and press [F12] to continue.
  18. Enter the PPN user name and password and press [F12] to continue.
  19. Login is performed.
  20. The Tester displays the message Login successful  . Press [F12] to continue.
  21. Follow the instructions on the Tester to select the required menu.
  22. Once the teaching process is completed successfully, the Tester shows the following status, for example:
    • 2 keys taught
    • Front BCM: taught
    • ELV: taught
    • Rear BCM: taught
    • DME: taught
    • Overall vehicle status: taught. Press [F12] to continue.
  23. Press [ESC] to exit the Online teaching function  and select the vehicle type  on the Start page.
  24. Read out the fault memory and erase it if necessary.
  25. Function test: Lock, open and start the vehicle using all remote controls (hand-held transmitters).
scientia non olet · About LEMON Manuals